Error message on a Windows Server 2003 Service Pack 1-based computer that is configured to use the Network Address Translation (NAT) functionality: "STOP: 0x000000D1 (parameter1 , 0x00000002, 0x00000000, 0xf27b4e8e)"

Article translations Article translations
Article ID: 926754 - View products that this article applies to.
Expand all | Collapse all

On This Page

SYMPTOMS

On a Microsoft Windows Server 2003 Service Pack 1 (SP1)-based computer that has the Routing and Remote Access service enabled and configured to use the Network Address Translation (NAT) functionality. The Windows Server 2003 SP1-based computer is in a high load Windows Server 2003 environment therefore, you may experience any one of the following symptoms:
  • Your computer automatically restarts.
  • After you log on, you receive the following error message:
    Microsoft Windows
    The system has recovered from a serious error.
    A log of this error has been created.
    Please tell Microsoft about this problem.
    We have created an error report that you can send to help us improve Microsoft Windows. We will treat this report as confidential and anonymous.
    To see what data this error report contains, click here .
    If the error message still appears and if you want to see the data that the error report contains, click the click here link at the bottom of the message box. You then see error signature information that may be similar to:
    BCCode : 000000D1 BCP1 : parameter1 BCP2 : 0x00000002 BCP3 : 0x00000000 BCP4 : 0xf27b4e8e OSVer : 5_2_3718 SP : 0_0 Product : 272_3
  • You receive the following "Stop" error message on a blue screen:
    A problem has been detected and Windows has been shut down to prevent damage to your computer...
    Technical information:

    *** STOP: 0x000000D1 (0xparameter1, 0x00000002, 0x00000000, 0xf27b4e8e)
    IRQL_NOT_LESS_OR_EQUAL Ipnat.sys
  • When you view the system log in Event Viewer, you may notice an event ID 1003 entry with information that is similar to:
    Date: date
    Source: System
    Error Time: time
    Category: (102)
    Type: Error
    Event ID: 1003
    User: N/A
    Computer: COMPUTER
    Description: Error code 000000D1, parameter1 parameter1, parameter2 0x00000002, parameter3 0x00000000, parameter4 0xf27b4e8e. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 30 30 30 30 30 30 35 00000D1 0020: 30 20 20 50 61 72 61 6d 0 Param 0028: 65 74 65 72 73 20 66 66 eters ff 0030: 66 66 66 66 64 31 2c

Notes

  • The symptoms of a Stop error vary according to your computer's system failure options. For additional information about how to configure system failure options, click the following article number to view the article in the Microsoft Knowledge Base:
    307973 HOW TO: Configure Recovery Options in Windows
  • The four parameters that are inside the parentheses of the technical information for the Stop error vary according to the computer's configuration.
  • Not all Stop 0x000000D1 errors are caused by the problem that is described in this article.

CAUSE

The problem may occur if a user uses IP preservation in a high load Windows Server 2003 SP1 environment. The IP NAT driver may incorrectly process the reset interface request in Windows Server 2003 SP1 .

RESOLUTION

This update has been superseded by a newer update. For information about the newer update, click the following article number to view the article in the Microsoft Knowledge Base:
931322 Error message on a Windows Server 2003 S931322 or SP2-based computer that is configured to use the Network Address Translation (NAT) functionality: "STOP: 0x000000D1 (parameter1 , 0x00000002, 0x00000000, 0xf27b4e8e)"

STATUS

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

Properties

Article ID: 926754 - Last Review: October 11, 2007 - Revision: 2.8
APPLIES TO
  • Microsoft Windows Server 2003 Service Pack 1, when used with:
    • Microsoft Windows Server 2003, Standard Edition (32-bit x86)
    • Microsoft Windows Server 2003, Enterprise Edition (32-bit x86)
    • Microsoft Windows Server 2003, Standard x64 Edition
    • Microsoft Windows Server 2003, Enterprise x64 Edition
    • Microsoft Windows Server 2003, Enterprise Edition for Itanium-based Systems
Keywords: 
kbwinserv2003presp2fix kbexpertiseinter kberrmsg kbbug kbfix kbqfe KB926754

Give Feedback

 

Contact us for more help

Contact us for more help
Connect with Answer Desk for expert help.
Get more support from smallbusiness.support.microsoft.com