Tuning TCP/IP for Performance

Article translations Article translations
Article ID: 93444 - View products that this article applies to.
Expand all | Collapse all

On This Page

Summary

The performance of Microsoft LAN Manager networks using TCP/IP can often be increased significantly by carefully tuning several stack parameters:

  • tcpsegmentsize (the maximum size of a single TCP segment)
  • tcpwindowsize (the amount of data a receiving TCP stack can buffer)
  • nbsessions (the maximum number of NetBIOS sessions available)
  • tcpconnections (the maximum number of TCP connections available)
For optimum performance, tcpsegmentsize should be the size of the MTU (maximum transfer unit) the media can handle, minus all headers up through the IP layer. LAN Manager TCP/IP allows sizes of 1450 bytes or less to be assigned to this parameter.

Also for optimum performance, tcpwindowsize should typically be as large as possible, in increments of tcpsegmentsize. Increasing tcpwindowsize, however, requires more memory, which can be a problem under MS-DOS. The TCP driver must load into a single 64K segment of memory. The driver must be able to buffer "tcpwindowsize" bytes of data on EACH tcpconnection, so the tcpwindowsize and tcpconnections values must be balanced against each other to achieve the best overall performance and connectivity.

More information

When a Microsoft LAN Manager TCP/IP workstation connects to a resource on a server, a TCP connection is established to the server unless one already exists. Next, a NetBIOS session is established over that TCP connection. If a second resource on the same server is requested, the SAME NetBIOS session and TCP connection are used, and activity for both resources is multiplexed over that single session and connection. However, any connections made using the Microsoft TCP/IP utilities for LAN Manager to other resources use one TCP connection each.

So, tuning can be reduced to a simple process:

  1. Determine the number of TCP connections needed on your workstation.
  2. Set nbsessions and TCPUTILS.INI parameters as appropriate.
  3. Use the table below to choose the largest possible tcpwindowsize.

Example

A "net use" command on the client shows:
Status      Local name     Remote name

OK          D:             \\server1\shareD
OK          E:             \\server1\shareE
OK          F:             \\server2\shareF
OK          G:             \\server2\shareG
OK          H:             \\server3\shareH
OK          I:             \\server3\shareI
OK          LPT1           \\server1\laser
OK          LPT2           \\server1\lineprint
				
Notice there are sessions to three servers, using three nbsessions, and three tcpconnections. In addition, assume you have the Microsoft TCP/IP Utilities for LAN Manager installed, and you use one telnet session and three sockets. By default, the value of nbsessions is 6, which allows some headroom for sessions to more LAN Manager servers.

The formula used internally for tcpconnections is:
   tcpconnections = nbsessions + 1 + [nsessions + numsockets]
				
Nsessions and numsockets exist only if the utilities are installed, and examining the TCPUTILS.INI file reveals their default values to be 2 and 8, respectively. (In LAN Manager 2.2, the value for numsockets is scheduled to change to 4).

So, if you are using LAN Manager version 2.1a or earlier, the default tcpconnections are 6 + 1 + 2 + 8 = 17. You only need one telnet connection and three sockets, so you should first reduce those parameters in TCPUTILS.INI. After the reduction, you are left with 6 + 1 + 1 + 3 = 11 tcpconnections. The table below shows that you can support a tcpwindowsize of no more than 2900 bytes on an MS-DOS client.
tcpconnections  tcpwindowsize  tcpsegmentsize
  6 or less         5800           1450
  7 - 8             4350           1450
  9 - 11            2900           1450  <-- Optimum configuration
 12 - 22            1450           1450      for 11 tcpconnections
				
You can add these parameters to the PROTOCOL.INI file in the [TCPIP_XIF] section. You should also modify the MS OS/2 server for versions 2.1 and 2.1a. In PROTOCOL.INI, set:
tcpsegmentsize=1450   (the same as for the clients)
tcpwindowsize=4350    (MS OS/2 normally has plenty of memory for this)
				
Microsoft no longer recommends setting the tcpconnections value in PROTOCOL.INI, and may remove the parameter in a future version. For the best results, adjust the parameters that are used to calculate tcpconnections and allow it to adjust internally.

Note that if you don't have the utilities installed and aren't using sockets or telnet, tcpconnections calculates to 6 + 1 = 7, so you would select a tcpwindowsize of 4350 from the above table.

NOTE: If your network adapter card is incapable of handling a tcpwindowsize burst of frames, it may drop one or more of them. If this occurs, performance will degrade seriously. Some older cards may be able to buffer only one incoming frame at a time.

The tcpwindowsize should be as large as possible within the memory constraints of the systems involved. On MS OS/2, tcpwindowsize should work at 4350 in all cases, and this will be the new default in LAN Manager 2.2. Performance gains will be most significant on high-delay networks such as those found in many WAN environments.

References

"Optimizing The Microsoft LAN Manager TCP/IP Protocol," a tech note available from Microsoft Inside Sales.

Properties

Article ID: 93444 - Last Review: May 26, 2014 - Revision: 2.0
Applies to
  • Microsoft LAN Manager 2.2 Standard Edition
Keywords: 
kbnetwork KB93444
Retired KB Content Disclaimer
This article was written about products for which Microsoft no longer offers support. Therefore, this article is offered "as is" and will no longer be updated.

Give Feedback

 

Contact us for more help

Contact us for more help
Connect with Answer Desk for expert help.
Get more support from smallbusiness.support.microsoft.com