Article ID: 139388 - Last Review: June 29, 2004 - Revision: 2.2

How To Create a Thermometer Bar in Visual FoxPro

View products that this article applies to.

This article was previously published under Q139388

SUMMARY

Windows-based applications often use a thermometer bar to represent the progress of a certain task visually. This article shows by example how to create a general-purpose thermometer bar that you can use in new or existing Visual FoxPro applications.

Back to the top

MORE INFORMATION

For this example, a timer is used to simulate a process. At regular intervals, the thermometer bar is updated to indicate the percentage of completion.

Back to the top

Step-by-Step Example

Create a new program that contains the following code:

   PUBLIC othermometer
   othermometer = CreateObject('thermometer')
   othermometer.Visible = .T.

   DEFINE CLASS thermometer AS form

           Height = 73
           Width = 385
           DoCreate = .T.
           AutoCenter = .T.
           Caption = ""
           Closable = .F.
           ControlBox = .F.
           MaxButton = .F.
           MinButton = .F.
           Movable = .F.
           Name = "Form1"

       ADD OBJECT shape2 AS shape WITH ;
           Height = 25, ;
           Left = 24, ;
           Top = 24, ;
           Width = 336, ;
           Name = "Shape2"

       ADD OBJECT shape1 AS shape WITH ;
           BackColor = RGB(0,0,255), ;
           Height = 25, ;
           Left = 24, ;
           Top = 24, ;
           Width = 0, ;
           Name = "Shape1"

       ADD OBJECT timer1 AS timer WITH ;
           Top = 0, ;
           Left = 0, ;
           Height = 23, ;
           Width = 23, ;
           Interval = 100, ;
           Name = "Timer1"

       PROCEDURE timer1.Timer
           IF This.Parent.shape1.Width<336
              This.Parent.shape1.Width=This.Parent.shape1.Width+2
           ELSE
              WAIT WINDOW 'Finished!'
              Thisform.Release
           ENDIF
       ENDPROC

   ENDDEFINE

Run the program. The thermometer bar form should display, and the thermometer bar should progress at a constant rate until it finishes.

Back to the top

Another Example

The previous example uses a timer to simulate a process. This example demonstrates how to implement this thermometer bar in a loop. The WAIT TIMEOUT command inside the loop represents where the developer would place code appropriate for the application.

The overall width of the thermometer bar is 300 pixels. Because the code in the loop is executed 100 times, the width of the thermometer is incremented 3 pixels at a time to achieve an overall thermometer bar width of 300 pixels. This incremental value will vary depending on the number of times through the loop.

   PUBLIC othermometer
   othermometer = CreateObject('thermometer')
   othermometer.Visible = .T.

   i=0
   SET CONSOLE OFF

   DO WHILE i<100
      WAIT TIMEOUT 1        && Place application-specific code here
      othermometer.update()
      i=i+1
   ENDDO

   WAIT WINDOW 'Finished'

   othermometer.Release

   DEFINE CLASS thermometer AS form

           Height = 73
           Width = 349
           DoCreate = .T.
           AutoCenter = .T.
           Caption = ""
           Closable = .F.
           ControlBox = .F.
           MaxButton = .F.
           MinButton = .F.
           Movable = .F.
           Name = "Form1"

       ADD OBJECT shape2 AS shape WITH ;
           Height = 25, ;
           Left = 24, ;
           Top = 24, ;
           Width = 300, ;
           Name = "Shape2"

       ADD OBJECT shape1 AS shape WITH ;
           BackColor = RGB(0,0,255), ;
           Height = 25, ;
           Left = 24, ;
           Top = 24, ;
           Width = 0, ;
           Name = "Shape1"

       ADD OBJECT timer1 AS timer WITH ;
           Top = 0, ;
           Left = 0, ;
           Height = 23, ;
           Width = 23, ;
           Interval = 100, ;
           Name = "Timer1"

       PROCEDURE update
          This.shape1.Width=This.shape1.Width+3
       ENDPROC

   ENDDEFINE

Back to the top