Article ID: 150737 - View products that this article applies to.
This article was previously published under Q150737
If a Windows NT server is running the Windows Internet Naming Service (WINS) and is participating in WINS database replication on the network, special consideration must be taken configuring where the WINS server points to for it's own name resolution (this parameter is set in the Network section of Control Panel, in the Configuration section of TCPIP Protocol).
We recommend that a WINS server point to itself as Primary WINS in the TCP/IP configuration. If you try to specify the same WINS address in the Secondary WINS address, you receive a "The WINS server is already in the list" error message. The configuration can be set by using the registry. However, because the address is already entered, you do not have to add it again.
We recommend that a WINS server always point to itself as Primary WINS only. This configuration avoids split registrations and other problems.
For additional information on some of these other problems, please see the following articles in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/135405/EN-US/ )Repairing a corrupted WINS database w/ starting version count
(http://support.microsoft.com/kb/168712/EN-US/ )How to manually recreate a WINS database
(http://support.microsoft.com/kb/150520/EN-US/ )WINS server sporadically loses name resolution
Microsoft has confirmed that this is a problem in the Microsoft products that are listed at the beginning of this article.
When any WINS enabled computer is booted it must register a variety of services with WINS. Commonly a computer has a Primary and Secondary WINS address configured in the TCP/IP setup. If the Primary WINS does not respond to the registrations, the computer tries the Secondary WINS.
For additional information on the services that can be registered, please see the following article(s) in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/119495/EN-US/ )List of Names Registered with WINS Service
Generally, most clients and servers should be configured with a Primary and Secondary WINS address, however caution must be taken with how a WINS server is itself configured. A WINS server eventually registers its services in its own local WINS database, regardless of whether it points to itself or not (either Primary, Secondary, or none). Registering with itself and another WINS server can cause problems when it comes to replication and renewal of these entries.
For example, if you have a WINS server ("Srv1") that points to itself as Primary and points to another WINS as Secondary ("Wins2"). When Srv1 is booted, it usually tries to register its services before its own WINS Service is started. Since those registrations fail, it tries to register them at Wins2. If Wins2 is available, it accepts the registration requests. However, not all the services are registered at Wins2, because as these registration requests are made, Srv1 continues to check its local WINS service. Once the service is running, it switches back to it and continues registering locally.
After replication has occurred between Srv1 and Wins2, both databases show this ownership:
Srv1: Owns his Srv1<20>, and Domain<1c> (if it is a domain controller)
Wins2: Owns all other Srv1 registrations, and also owns Domain<1c> from Srv1
This potentially problematic condition is referred to as "split registration."
At this point, Srv1 has reverted to re-registering locally, however it takes a while before you can see it. Meanwhile, Srv1 and Wins2 are replicating the split registration mappings to other WINS servers. Eventually these replicas should be reconciled at the remote WINS (that is, the Wins2 replicas are replaced by the newer Srv1 replicas). However, before reconciliation is finished, client connection problems may have occurred, including the inability to connect to a WINS server that split its registration (in this example, Srv1), or the inability to resolve the domain<1c> name that Srv1 registered.
The exact conditions that lead to failure are varied. If your WINS servers are running Windows NT version 3.51 with Service Pack 4 (or greater), these conditions should only be temporary. However, the problem may be more severe depending on your replication scheme or if you are running pre- Service Pack 4 WINS servers.
Another faulty configuration is setting a remote IP address (in this example, Wins2) as Primary while setting the local WINS (Srv1) as Secondary. In this case, Srv1 will eventually stop refreshing its NetBIOS lease at Wins2, and will begin registering locally. Depending on your WINS replication scheme, this may cause connection problems.
Article ID: 150737 - Last Review: February 21, 2007 - Revision: 4.3
Contact us for more help