Default Gateway Configuration for Multihomed Computers

Article ID: 157025 - View products that this article applies to.
This article was previously published under Q157025
Notice
This article applies to Windows 2000. Support for Windows 2000 ends on July 13, 2010. The Windows 2000 End-of-Support Solution Center
(http://support.microsoft.com/?scid=http%3a%2f%2fsupport.microsoft.com%2fwin2000)
is a starting point for planning your migration strategy from Windows 2000. For more information see the Microsoft Support Lifecycle Policy
(http://support.microsoft.com/lifecycle/)
.
Expand all | Collapse all

SUMMARY

A multihomed computer is one that has multiple network interfaces. For computers using TCP/IP, these interfaces can be separate network interface cards (NICs) or multiple IP addresses on one NIC. This article discusses the recommended method of configuring the default gateway on multihomed computers.

MORE INFORMATION

In the TCP/IP properties of each of the products listed above, you have the option to configure a default gateway for each NIC or multiple default gateways for the same NIC. Every NIC that has a default gateway adds a 0.0.0.0 route (default route) to the routing table.

In either case, the TCP/IP routing table will have multiple default routes listed (to view the routing table, type "ROUTE PRINT" from the command prompt). The route most likely to be used is the default gateway for the primary NIC that is bound to TCP/IP, but this is not always the case. If the Transmission Control Protocol (TCP) session on the active default gateway times out, TCP can switch to the next default gateway. This can present a problem depending on your network configuration.

It is not recommended to have multiple adapters configured on the same network (it may even create more overhead). For more information on TCP/IP behavior when multiple adapters are configured on the same network, please see the following article in the Microsoft Knowledge Base:
175767
(http://support.microsoft.com/kb/175767/EN-US/ )
Expected Behavior of Multiple Adapters on Same Network
If both NICs are on the same contiguous network, this should not be a problem as long as the default gateways are valid. However, if the NICs are configured on disjoint networks, or networks that are physically separated and cannot communicate with each other, you will not be able to communicate with the destination host reliably.

A common use of multiple default gateways is to configure a backup gateway in the event of a failure of the primary gateway (router). This backup gateway is used by dead gateway detection, and is only triggered with TCP or connection-oriented traffic. Utilities like PING cannot force the default gateway to switch, because these utilities use User Datagram Protocol (UDP) and Internet Control Message Protocol (ICMP).

For additional information, please see the following articles in the Microsoft Knowledge Base:
128978
(http://support.microsoft.com/kb/128978/EN-US/ )
Dead Gateway Detection in TCP/IP for Windows NT
171564
(http://support.microsoft.com/kb/171564/EN-US/ )
TCP/IP Dead Gateway Detection Algorithm Updated for Windows NT
Only one default gateway should be configured on any multihomed computer. The default gateway is a global configuration for the server, not a setting that must be set for each network adapter. The server is already aware of all the networks it is directly connected to, and adds a route to each network for which it has a TCP/IP address.

The default gateway is used only for traffic that needs to go to a network for which the server has no route. There is only one default gateway active for a computer at a time. You should generally configure the default gateway on the most complex network, and leave the field blank on the other adapter. However, if fault tolerance is desired, choose one of the following:

  • If multiple routers are available on the same subnet, configure one (or more) default gateways on the same network adapter. This allows you to know which one is actually the primary. Leave all other adapters' default gateway configuration blank. -or-

  • If the adapters on the multihomed computer are on disjoint networks (subnets that are not connected by a router), configure one (or more) default gateways on the same network adapter and use static routes for the remote networks that are reached through the network adapter with no default gateway. -or-

  • Use a Routing Information Protocol (RIP) listener by enabling silent RIP and broadcasting available default routes with unique costs. The preferred default gateway can be the one advertised with the lowest cost. For more information, please see the following article in the Microsoft Knowledge Base:
    169161
    (http://support.microsoft.com/kb/169161/EN-US/ )
    Registry Parameters for RIP for IP Version 1
    -or-
  • The simplest way to control the ordering of default gateways is to add only a single default gateway through the TCP/IP properties in Control Panel and add any additional gateways using the command line utility Route.exe. By providing a unique cost for each gateway, the ordering of the gateways can be easily determined.

Properties

Article ID: 157025 - Last Review: February 22, 2007 - Revision: 3.3
APPLIES TO
  • Microsoft Windows 2000 Server
  • Microsoft Windows 2000 Advanced Server
  • Microsoft Windows 2000 Professional Edition
  • Microsoft Windows NT Advanced Server 3.1
  • Microsoft Windows NT Workstation 3.1
  • Microsoft Windows NT Workstation 3.5
  • Microsoft Windows NT Workstation 3.51
  • Microsoft Windows NT Workstation 4.0 Developer Edition
  • Microsoft Windows NT Advanced Server 3.1
  • Microsoft Windows NT Server 3.5
  • Microsoft Windows NT Server 3.51
  • Microsoft Windows NT Server 4.0 Standard Edition
  • Microsoft Windows for Workgroups 3.11
  • Microsoft TCP/IP for Windows for Workgroups 3.11
  • Microsoft TCP/IP for Windows for Workgroups 3.11a
  • Microsoft TCP/IP for Windows for Workgroups 3.11b
  • Microsoft Windows 95
Keywords: 
kbinfo kbnetwork KB157025
Back to the top | Give Feedback

Give Feedback

 
Back to the topBack to the top