Article ID: 186550 - View products that this article applies to.
This article was previously published under Q186550
Recursion too deep, stack overflowed.
The window cannot act on the sent message.
Cannot complete this function.
The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupt.
The volume for a file has been externally altered such that the opened file is no longer valid.
The requested operation cannot be performed in full-screen mode.
An attempt was made to reference a token that does not exist.
The configuration registry database is corrupt.
The configuration registry key is invalid.
The configuration registry key could not be opened.
The configuration registry key could not be read.
The configuration registry key could not be written.
One of the files in the Registry database had to be recovered by use of a log or alternate copy. The recovery was successful.
The Registry is corrupt. The structure of one of the files that contains Registry data is corrupt, or the system's image of the file in memory is corrupt, or the file could not be recovered because the alternate copy or log was absent or corrupt.
An I/O operation initiated by the Registry failed unrecoverably. The Registry could not read in, or write out, or flush, one of the files that contain the system's image of the Registry.
The system has attempted to load or restore a file into the Registry, but the specified file is not in a Registry file format.
Illegal operation attempted on a Registry key which has been marked for deletion.
System could not allocate the required space in a Registry log.
Cannot create a symbolic link in a Registry key that already has subkeys or values.
Cannot create a stable subkey under a volatile parent key.
A notify change request is being completed and the information is not being returned in the caller's buffer. The caller now needs to enumerate the files to find the changes.
A stop control has been sent to a service which other running services are dependent on.
The requested control is not valid for this service
The service did not respond to the start or control request in a timely fashion.
A thread could not be created for the service.
The service database is locked.
An instance of the service is already running.
The account name is invalid or does not exist.
The specified service is disabled and cannot be started.
Circular service dependency was specified.
The specified service does not exist as an installed service.
The service cannot accept control messages at this time.
The service has not been started.
The service process could not connect to the service controller.
An exception occurred in the service when handling the control request.
The database specified does not exist.
The service has returned a service-specific error code.
The process terminated unexpectedly.
The dependency service or group failed to start.
The service did not start due to a logon failure.
After starting, the service hung in a start-pending state.
The specified service database lock is invalid.
The specified service has been marked for deletion.
The specified service already exists.
The system is currently running with the last-known-good configuration.
The dependency service does not exist or has been marked for deletion.
The current boot has already been accepted for use as the last-known- good control set.
No attempts to start the service have been made since the last boot.
The name is already in use as either a service name or a service display name.
The account specified for this service is different from the account specified for other services running in the same process.
The physical end of the tape has been reached.
A tape access reached a filemark.
Beginning of tape or partition was encountered.
A tape access reached the end of a set of files.
No more data is on the tape.
Tape could not be partitioned.
When accessing a new tape of a multivolume partition, the current blocksize is incorrect.
Tape partition information could not be found when loading a tape.
Unable to lock the media eject mechanism.
Unable to unload the media.
Media in drive may have changed.
The I/O bus was reset.
No media in drive.
No mapping for the Unicode character exists in the target multi-byte code page.
A dynamic link library (DLL) initialization routine failed.
A system shutdown is in progress.
Unable to abort the system shutdown because no shutdown was in progress.
The request could not be performed because of an I/O device error.
No serial device was successfully initialized. The serial driver will unload.
Unable to open a device that was sharing an interrupt request (IRQ) with other devices. At least one other device that uses that IRQ was already opened.
A serial I/O operation was completed by another write to the serial port. (The IOCTL_SERIAL_XOFF_COUNTER reached zero.)
A serial I/O operation completed because the time-out period expired. (The IOCTL_SERIAL_XOFF_COUNTER did not reach zero.)
No ID address mark was found on the floppy disk.
Mismatch between the floppy disk sector ID field and the floppy disk controller track address.
The floppy disk controller reported an error that is not recognized by the floppy disk driver.
The floppy disk controller returned inconsistent results in its registers.
While accessing the hard disk, a recalibrate operation failed, even after retries.
While accessing the hard disk, a disk operation failed even after retries.
While accessing the hard disk, a disk controller reset was needed, but even that failed.
Physical end of tape encountered.
Not enough server storage is available to process this command.
A potential deadlock condition has been detected.
The base address or the file offset specified does not have the proper alignment.
An attempt to change the system power state was vetoed by another application or driver.
The system BIOS failed an attempt to change the system power state.
An attempt was made to create more links on a file than the file system supports.
The specified program requires a newer version of Windows.
The specified program is not a Windows or MS-DOS program.
Cannot start more than one instance of the specified program.
The specified program was written for an older version of Windows.
One of the library files needed to run this application is damaged.
No application is associated with the specified file for this operation.
An error occurred in sending the command to the application.
One of the library files needed to run this application cannot be found.
Contact us for more help
Connect with Answer Desk for expert help.