Direct hosting of SMB over TCP/IP

Article translations Article translations
Article ID: 204279 - View products that this article applies to.
This article was previously published under Q204279
Expand all | Collapse all

SUMMARY

Windows supports file and printer sharing traffic by using the Server Message Block (SMB) protocol directly hosted on TCP. This differs from earlier operating systems, in which SMB traffic requires the NetBIOS over TCP (NBT) protocol to work on a TCP/IP transport. Removing the NetBIOS transport has several advantages, including:
  • Simplifying the transport of SMB traffic.
  • Removing WINS and NetBIOS broadcast as a means of name resolution.
  • Standardizing name resolution on DNS for file and printer sharing.
If both the direct hosted and NBT interfaces are enabled, both methods are tried at the same time and the first to respond is used. This allows Windows to function properly with operating systems that do not support direct hosting of SMB traffic.

MORE INFORMATION

NetBIOS over TCP traditionally uses the following ports:
   nbname            137/UDP
   nbname            137/TCP
   nbdatagram        138/UDP
   nbsession         139/TCP
				
Direct hosted "NetBIOS-less" SMB traffic uses port 445 (TCP and UDP). In this situation, a four-byte header precedes the SMB traffic. The first byte of this header is always 0x00, and the next three bytes are the length of the remaining data.

Use the following steps to disable NetBIOS over TCP/IP; this procedure forces all SMB traffic to be direct hosted. Take care in implementing this setting because it causes the Windows-based computer to be unable to communicate with earlier operating systems using SMB traffic:
  1. Click Start, point to Settings, and then click Network and Dial-up Connection.
  2. Right-click Local Area Connection, and then click Properties.
  3. Click Internet Protocol (TCP/IP), and then click Properties.
  4. Click Advanced.
  5. Click the WINS tab, and then click Disable NetBIOS over TCP/IP.
You can also disable NetBIOS over TCP/IP by using a DHCP server with Microsoft vendor-specific option code 1, ("Disable NetBIOS over TCP/IP"). Setting this option to a value of 2 disables NBT. For more information about using this method, refer to the DHCP Server Help file in Windows.

To determine if NetBIOS over TCP/IP is enabled on a Windows-based computer, issue a net config redirector or net config server command at a command prompt. The output shows bindings for the NetbiosSmb device (which is the "NetBIOS-less" transport) and for the NetBT_Tcpip device (which is the NetBIOS over TCP transport). For example, the following sample output shows both the direct hosted and the NBT transport bound to the adapter:
   Workstation active on
      NetbiosSmb (000000000000)
      NetBT_Tcpip_{610E2A3A-16C7-4E66-A11D-A483A5468C10} (02004C4F4F50)
      NetBT_Tcpip_{CAF8956D-99FB-46E3-B04B-D4BB1AE93982} (009027CED4C2)
				
NetBT_Tcpip is bound to each adapter individually; an instance of NetBT_Tcpip is shown for each network adapter that it is bound to. NetbiosSmb is a global device, and is not bound on a per-adapter basis. This means that direct-hosted SMB's cannot be disabled in Windows without disabling File and Printer Sharing for Microsoft Networks completely.

Properties

Article ID: 204279 - Last Review: October 11, 2007 - Revision: 4.4
APPLIES TO
  • Microsoft Windows 2000 Server
  • Microsoft Windows 2000 Advanced Server
  • Microsoft Windows 2000 Professional Edition
  • Microsoft Windows XP Home Edition
  • Microsoft Windows XP Professional
  • Microsoft Windows XP Professional x64 Edition
  • Microsoft Windows Server 2003, Enterprise Edition (32-bit x86)
  • Microsoft Windows Server 2003, Standard Edition (32-bit x86)
  • Microsoft Windows XP 64-Bit Edition Version 2003
Keywords: 
kbinfo kbenv kbnetwork KB204279

Give Feedback

 

Contact us for more help

Contact us for more help
Connect with Answer Desk for expert help.
Get more support from smallbusiness.support.microsoft.com