Important This article contains information that shows you how to help lower security settings or how to turn off security features on a computer. You can make these changes to work around a specific problem. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this workaround in your particular environment. If you implement this workaround, take any appropriate additional steps to help protect the computer.
If you are a Small Business customer, find additional troubleshooting and learning resources at the Support for Small Business site.
The Microsoft Forefront Threat Management Gateway (TMG) 2010 Enterprise Edition server is running Microsoft Enterprise Management Server (EMS) in the headquarters network.
The TMG 2010 server that is installed on the branch office network is connected to the headquarters EMS using a Site to Site VPN that is hosted on the TMG 2010 server.
In this scenario, an installation of Service Pack 1 or Service Pack 2 on the branch office fails just after Setup stops the Firewall service. Then, the EMS connectivity problem is reported, and the Setup process roll backs the service pack installation. For more information about the ISA and TMG branch office scenario, visit the following Microsoft TechNet webpage:
This problem occurs because the installation process must shut down the Microsoft Forefront TMG Firewall service to update binary files. When the service is stopped, the Site to Site VPN connection to the branch office network from the headquarters EMS server is closed. When this occurs, the installation process loses connection to the headquarters EMS server.
In this command, the placeholder a.b.c.d is the external address of the headquarters TMG server. This adds a Firewall Engine exception to enable the headquarters TMG server to connect to the branch office TMG network even when it is in lockdown mode (that is, when the TMG service is down).
Create a new dial-up connection:
Open Network and Sharing Center.
Click A new connection or network.
Connect to a workplace.
Click Use my Internet connection (VPN).
Click I’ll set up an Internet connection later.
Type the external address of the headquarters TMG network.
Type the user credentials. Use the headquarters TMG computer name as the domain.
Right-click the new connection, click Properties, and then click the Security tab:
For Type of VPN Connection, select L2TP/IPSec.
Under Advanced settings, click Use preshared key for authentication.
Make sure that the configuration on the headquarters TMG server is synced by using the Monitoring tab. Connect to the headquarters TMG network by using the newly created connection.
On the headquarters TMG after a VPN client connection is established:
In the headquarters TMG 2010 user interface, under Monitoring, click Sessions, and then confirm that a new VPN Client session was established.
Add a rule that enables all traffic from VPN Clients to Internal and Local Host networks for all users. Create the opposite rule enabling Internal plus Local Host to VPN Clients for all users.
Make sure that there is a respective network routing rule. The default VPN Clients to Internal Network would be sufficient for the routing rule.
On the branch office TMG server by using your existing remote connection:
Stop the Firewall service. To do this, at a command prompt with Administrative permissions, type the following:
net stop /y fwsrv
This also stops the Routing and Remote Access service and disconnects the existing Site to Site connection.
Install TMG 2010 SP1 by typing the following command:
Msiexec /p <full msp path> /L*v <full log path>
On the Locate Configuration Storage Server wizard page, provide explicit credentials. Do not use the Current user option.
After you successfully install TMG 2010 SP1, restart the computer if you have to. Then, if you have to, manually start the Firewall service and verify that the Site to Site tunnel is restored.
Disconnect the VPN client connection.
On the headquarters TMG server after you successfully upgrade the branch office TMG server:
Upgrade the headquarters TMG 2010 server to Service Pack 1. Please be aware that in order to be able to see the branch office TMG server’s configuration on the headquarters TMG server, you must first upgrade the headquarters TMG server to Service Pack 1.
Clean up after upgrade
On the headquarters TMG server:
Restore the VPN Client access configuration that you set in the "Upgrade process: On the headquarters TMG server" procedure. If the Routing and Remote Access service restarts, you may have to wait for several minutes until all the services are started.
Delete the user that was created in step 6 of the "Upgrade process: On the headquarters TMG server" procedure.
On the branch office TMG server:
Delete Firewall Engine exceptions created in step 1 of the "On the branch office TMG server when it is connected" procedure. To do this, follow these steps:
Open a command prompt with Administrative permissions.
Run the following command:
netsh tmg show all
In the command output, locate any dynamic and persistent IDs that corresponds to the IP range that you added in the "Upgrade process: On the headquarters TMG server" procedure.
Run the following commands. Use values for x that correspond to the dynamic IDs and use values for y that correspond to the persistent IDs that you found in step 1.c.:
netsh tmg delete allowedrange id=x
netsh tmg delete allowedrange id=y persistent
Delete the dial-up connection that you created in step 2 of the "Upgrade process: On the branch office TMG server when it is connected" procedure.