In Exchange 2000 and Exchange 2003, the Simple Mail
Transfer Protocol (SMTP) connector replaces the Internet Mail Service in
earlier versions of Exchange for mixed mode environments. However, it should be
noted that in pure Exchange 200x environments, a connector is not a requirement
for Internet mail flow. This article explains how to configure the SMTP
Exchange 2000 and Exchange 2003 work differently than
Exchange Server 5.5. SMTP is an add-on to Exchange Server 5.5 through Internet
Mail Service. SMTP is native to Exchange 2000 and Exchange 2003. Everything is
SMTP-based. The default SMTP virtual server,
can handle all Internet traffic (inbound and outbound).
the main reason for an SMTP connector is either to send mail a certain way to a
certain domain (for example, to forward messages to a specific smart host for
that domain only or to send HELO instead of EHLO) or to take the place of an
IMS in an environment that includes Exchange Server 5.5.
and securely configure the SMTP connector
follow these steps:
- Start Exchange System Manager.
After you install Exchange Server in an Exchange 2003 organization or in an Exchange 2000
organization, Exchange System Manager does not automatically display
routing groups and administrative groups. You must configure the Exchange
organization to display routing groups and administrative groups.
For more information
about how to configure Exchange System Manager to display routing groups and
administrative groups in Exchange server, click the following article number to view the article in the Microsoft Knowledge Base:
How to configure System Manager to display routing and administrative groups in
Exchange 2000 Server
- Expand the Administrative Groups container. To do so, click
the plus sign (+) to the left of the container.
- Click the administrative group that you want to work with,
and then expand it.
- Expand the Routing Groups container.
- Click the routing group that you want to work with, and
then expand it.
- Click the Connectors container. Right-click the Connectors container, and then click New.
- Click SMTP Connector.
- On the General tab, provide an appropriate identifying name for the
- Choose to use DNS or forward to a smart host (if you are
relaying through an Internet service provider send-mail server). If you are
forwarding to a smart host, use the IP address of the smart host in square
- Under Local Bridgeheads, click Add. Add the server that becomes the bridgehead server for the
routing group. Designate an SMTP virtual server as a bridgehead server for the
SMTP connector. This can be either the server that you are working on or
another server in the same routing group. Alternatively, this duty can be
shared by multiple servers.
Important You can configure an SMTP virtual server to use a
TCP (Listening) port that differs from the default SMTP port 25. You must make sure
that the SMTP virtual server that you select as a local bridgehead for the SMTP
connector has a TCP (Listening) port that equals 25. When you do this, the SMTP
virtual server can be reached by other SMTP virtual servers that have the
default TCP (Outgoing) port 25.
For more information, click the following article number to view the article in the Microsoft Knowledge Base:
How to change SMTP port 25 to another port in Microsoft Exchange Server
- Click the Address Space tab. Under Connector Scope, click either Entire Organization or Routing Group. As in earlier versions of Exchange Server, when you configure
the Internet Mail Service, click Add, click SMTP, and then click OK. Accept the default (*) unless you require outbound e-mail domain
restriction, and leave the cost as 1. If you have accepted the default of (*),
you should never click to select the Allow messages to be relayed to
these domains check box. Clicking to select the Allow messages
to be relayed to these domains check box would open your server for
relay to the world. The Allow messages to be relayed to these
domains check box should be for secure domain to domain connections
- If you have chosen forward all mail to a smart host, click
the Advanced tab. Click the Outbound Security option, and then select an appropriate authentication method for
your relay host. The default is Anonymous Access. Anonymous is the method that
must be used if you are forwarding to an ISP, unless you have made prior
arrangements with the ISP for another security level. If you are forwarding to
your own server or to another server outside your environment, work with the
administrator of that server to select the appropriate security level for both
servers. You can add more than one smart host in this box by using the
- Click OK to exit Outbound Security.
- Click OK to exit the Advanced tab.
- Click OK to exit the SMTP connector.
- You must restart the Microsoft Exchange Routing Engine
service and the SMTP service for these changes to take effect.
Article ID: 265293 - Last Review: October 25, 2007 - Revision: 5.4
- Microsoft Exchange Server 2003 Enterprise Edition
- Microsoft Exchange Server 2003 Standard Edition
- Microsoft Exchange 2000 Server Standard Edition