The basics about universal serial bus (USB) device driver development

Article translations Article translations
Article ID: 323594 - View products that this article applies to.
This article was previously published under Q323594
Expand all | Collapse all

On This Page

SUMMARY

With the growing popularity of the universal serial bus (USB), many hardware vendors must offer a USB interface for devices that currently support only serial or parallel interface.

This article discusses the following:
  • Important differences between the USB interface and the serial or parallel interfaces
  • Why user mode applications cannot directly access a USB device
  • The basic resources that are required to develop the driver for a newly designed USB device

MORE INFORMATION

Complexity

Compared to serial or parallel ports, the USB is a complex bus. For example, each device that is connected to this bus receives an address, and packets of data are exchanged between the host computer and the addressed device. Additionally, devices can operate at multiple speeds, and devices can be temporarily disconnected from the bus if they do not understand high speed transfers. In general, data transfer on USBs is much more complex and relies on a well-defined protocol that is similar, in some respects, to a low-level network protocol.

For these reasons, USB devices incorporate some "intelligence" so they can correctly handle data packets that are exchanged over the USB. It is not generally possible to implement a USB interface by using discrete electronic components or small scale integrate or medium scale integrate circuits like you can on serial and parallel interfaces. Rather, a microprocessor is typically used on the device to handle communication over the USB.

Because a USB device is complex, you cannot just open and access a USB device from a User Mode application. At the hardware level, a USB device offers several endpoints. The host can establish a pipe that is connected to each endpoint, and can talk to the device through this pipe. You have to do this work in kernel mode. Therefore, a USB device must have an associated driver. The Plug and Play architecture also requires a driver, because as soon as you plug in the device, the system tries to find a suitable driver for it.

Sample driver

A sample in the Windows DDK, which is named BulkUSB (DDKdir\src\wdm\usb\bulkusb), allows a user mode application to read from and to write raw data directly to the endpoint of the USB device. The basic job of the sample driver is to copy data to and from the application and the endpoint. You can easily adapt this sample to almost any USB device. However, commercial devices must typically do the following:
  • Have a more complete device driver, which abstracts its functionality.
  • Offer a higher level programming interface to the user mode application.
  • Comply with a specific device interface class (if the device is a common peripheral type).
In summary, there are limited scenarios where this sample can be used with no or little customization:
  • For testing purposes
  • To familiarize you with USB driver development
  • For very simple devices that you know in advance will be accessed by one specific program

Portability

A USB device driver that is written for Windows XP and for Windows 2000 using only Windows Driver Model (WDM) functions is portable to Windows Millennium Edition and to Windows 98, generally with few or no changes. For additional information about how to port WDM drivers from Windows XP or from Windows 2000 to Windows Millennium Edition or to Windows 98, see the "References" section (Walter Oney's book, Appendix A).

Third-party resources

Some third-party vendors offer pre-built chipsets, which you can incorporate to implement the USB interface. Many vendors also offer hardware development kits with which you can build prototypes around their chipset. For more information, see the "References" section of this article (Walter Oney's book, chapter 11).

Some third-party vendors offer generic USB drivers, which you can customize by using data files without having to use kernel mode programming. Some companies also offer ActiveX components (for example, OCXs) to access their driver from OLE automation clients, such as Microsoft Visual Basic.

REFERENCES

  • Universal Serial Bus System Architecture 2nd Edition, Don Anderson/Dave Dzatko, Mindshare Inc, Addison Wesley, ISBN 0-201-30975-0.
  • Windows Driver Development Kit, System Support for Buses, USB, Design Reference.
For more information about how to develop your own product from chipsets that are provided by a third-party vendor, or how to port WDM drivers, see the following book:
  • Programming the Microsoft Windows Driver Model, Walter Oney, Microsoft Press, ISBN 0-7356-0588-2. (This article specifically mentions Chapter 11 and Appendix A.)

Properties

Article ID: 323594 - Last Review: August 9, 2005 - Revision: 3.0
APPLIES TO
  • Microsoft Windows XP Driver Development Kit
  • Microsoft Win32 Device Driver Kit for Windows 2000
  • Microsoft Windows Server 2003 Driver Development Kit
Keywords: 
kbinfo KB323594

Give Feedback

 

Contact us for more help

Contact us for more help
Connect with Answer Desk for expert help.
Get more support from smallbusiness.support.microsoft.com