Article ID: 325590 - View products that this article applies to.
This article was previously published under Q325590
Expand all | Collapse all

On This Page

SUMMARY

This article describes the following:
  • How to use the Diskpart.exe command prompt utility to extend a data volume into unallocated space in Windows Server 2003, in Windows XP, and in Microsoft Windows 2000.
  • How to extend the boot partition in Windows Server 2008.

MORE INFORMATION

How to use Diskpart.exe to extend a data volume in Windows Server 2003, in Windows XP, and in Windows 2000

You can use the Diskpart.exe utility to manage disks, partitions, and volumes from a command-line interface. You can use Diskpart.exe on both Basic disks and Dynamic disks. If an NTFS volume resides on a hardware RAID 5 container that can add space to the container, you can extend the NTFS Volume with Diskpart.exe while the disk remains a Basic disk.

Use the extend command to incorporate unallocated space into an existing volume while preserving the data.

The following are the requirements for the extend command:
  • The volume must be formatted with the NTFS file system.
  • For Basic volumes, the unallocated space for the extension must be the next contiguous space on the same disk.
  • For Dynamic Volumes, the unallocated space can be any empty area on any Dynamic disk on the system.
  • Only the extension of data volumes is supported. System or boot volumes may be blocked from being extended, and you may receive the following error:
    Diskpart failed to extend the volume. Please make sure the volume is valid for extending
  • You cannot extend the partition if the system page file is located on the partition. Move the page file to a partition that you do not want to extend.
To extend a partition or volume, you must first select the volume to give it the focus, and then you can specify how large to make the extension. To extend a volume, follow these steps:
  1. At a command prompt, type diskpart.exe.
  2. Type list volume to display the existing volumes on the computer.
  3. Type Select volume volume number where volume number is number of the volume that you want to extend.
  4. Type extend [size=n] [disk=n] [noerr]. The following describes the parameters:
    size=n
    The space, in megabytes (MB), to add to the current partition. If you do not specify a size, the disk is extended to use all the next contiguous unallocated space.

    disk=n
    The dynamic disk on which to extend the volume. Space equal to size=n is allocated on the disk. If no disk is specified, the volume is extended on the current disk.

    noerr
    For scripting only. When an error is thrown, this parameter specifies that Diskpart continue to process commands as if the error did not occur. Without the noerr parameter, an error causes Diskpart to exit with an error code.
  5. Type exit to exit Diskpart.exe.
When the extend command is complete, you should receive a message that states that Diskpart successfully extended the volume. The new space should be added to the existing drive while maintaining the data on the volume.

Note In Windows XP and in Windows 2000, you cannot use Diskpart.exe to extend a simple volume on a Dynamic disk that was originally created on a Basic disk. You can extend only simple volumes that were created after the disk was upgraded to Dynamic disk. If you try to extend a simple volume on a Dynamic disk that was originally created on a Basic disk, you receive the following error message. This restriction was removed in Windows Server 2003.
Diskpart failed to extend the volume.
Please make sure the volume is valid for extending
Note Windows Server 2003 and Windows XP include Diskpart.exe as part of the base operating system.

To download the Diskpart.exe commandprompt utility for Windows 2000, visit the following Microsoft Web site:
http://www.microsoft.com/downloads/details.aspx?FamilyID=0fd9788a-5d64-4f57-949f-ef62de7ab1ae&displaylang=en
Note The link to download Diskpart.exe is only for Windows 2000. For Windows Server 2003 and for Windows XP, use the Diskpart.exe tool that is built in to these operating systems.

Note We recommend that you contact your system vendor for updated BIOS, firmware, drivers, and agents before you convert to Dynamic disks.

How to extend the boot partition in Windows Server 2008

To extend the boot partition in Windows Server 2008, follow these steps:
  1. Click Start, and then click Server Manager.
  2. In the navigation pane, expand Storage, and then click Disk Management.
  3. In the details pane, right-click the volume that you want, and then click Extend Volume.
  4. Follow the instructions in the Extend Volume Wizard to extend the boot partition.
Note You can only extend the boot partition in contiguous unallocated disk space.

Properties

Article ID: 325590 - Last Review: September 11, 2011 - Revision: 14.0
APPLIES TO
  • Microsoft Windows Server 2003, Standard Edition (32-bit x86)
  • Microsoft Windows Server 2003, Web Edition
  • Microsoft Windows Server 2003, Enterprise Edition (32-bit x86)
  • Microsoft Windows Server 2003, Enterprise Edition for Itanium-based Systems
  • Microsoft Windows XP Home Edition
  • Microsoft Windows XP Professional
  • Microsoft Windows 2000 Server
  • Microsoft Windows 2000 Advanced Server
  • Microsoft Windows 2000 Professional Edition
  • Windows Server 2008 for Itanium-Based Systems
  • Windows Server 2008 Datacenter
  • Windows Server 2008 Enterprise
  • Windows Server 2008 Standard
Keywords: 
kbsurveynew kbexpertiseadvanced kbinfo w2000basic w2000fs w2000ft KB325590

Give Feedback

 

Contact us for more help

Contact us for more help
Connect with Answer Desk for expert help.
Get more support from smallbusiness.support.microsoft.com