Article ID: 329632 - Last Review: September 8, 2005 - Revision: 4.5

How to obtain and to install USB 2.0 drivers in Windows XP Service Pack 1

View products that this article applies to.
System TipThis article applies to a different operating system than the one you are using. Article content that may not be relevant to you is disabled.
This article was previously published under Q329632

To continue receiving security updates for Windows, make sure you're running Windows XP with Service Pack 3 (SP3). For more information, refer to this Microsoft web page: Support is ending for some versions of Windows (http://windows.microsoft.com/en-us/windows/help/end-support-windows-xp-sp2-windows-vista-without-service-packs)

The third-party products that this article discusses are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, regarding the performance or reliability of these products.

On This Page

Expand all | Collapse all

INTRODUCTION

This article describes the availability of universal serial bus (USB) 2.0 driver support in Microsoft Windows XP Service Pack 1.
Back to the top

MORE INFORMATION

USB 2.0 support for any Enhanced Host Controller Interface (EHCI) compliant host controller is available in Windows XP Service Pack 1 (SP1). If you have recently installed Windows XP Service Pack 1 on your computer, follow the directions in this article to obtain the latest USB 2.0 drivers.
Back to the top

How to determine whether you do not have to upgrade

You do not have to upgrade the USB 2.0 support if any one of the following conditions is true:
  • You purchase a new USB 2.0-capable system that came with Windows XP Service Pack 1 pre-installed. Your original equipment manufacturer (OEM) makes sure that the system has the latest USB 2.0 driver stack.
  • You already have Windows XP Service Pack 1 installed on the computer. You add a new USB 2.0 compatible PCI add-in card. In this situation, the latest Windows XP Service Pack 1 drivers for USB 2.0 are auto-selected during driver installation.
  • You purchase and install Windows XP with Service Pack 1 included on the CD-ROM.
  • You purchase a system from an OEM that slipstreams and pre-installs Windows XP Service Pack 1. Your OEM makes sure that the appropriate USB 2.0 drivers are identified and are installed on the system during GUI-mode install.
Back to the top

How to upgrade to the USB 2.0 Enhanced Host Controller driver in Windows XP Service Pack 1

If your computer supports USB 2.0, and you have a pre-installed USB 2.0 driver from the OEM, you can continue to use the earlier pre-installed drivers for USB 2.0. You can do this even after you install Windows XP Service Pack 1.

To upgrade to the USB 2.0 Enhanced Host Controller driver in Windows XP Service Pack 1, follow these steps:
  1. Make sure that Windows XP Service Pack 1 is installed. Make sure that you have restarted your computer if you receive a message to do this.

    For more information about Windows XP Service Pack 1, visit the following Microsoft Web site:
    http://technet.microsoft.com/en-us/library/cc768378.aspx (http://technet.microsoft.com/en-us/library/cc768378.aspx)
  2. Open Device Manager. Locate Devices by Type.

    To open Device Manager, either run Devmgmt.msc at a command prompt, or follow these steps:
    1. Click Start, right-click My Computer, and then click Manage.
    2. Expand System Tools, click Device Manager, and then click Devices by type on the View menu.
  3. Right-click USB 2.0 EHCI Host controller, and then click Update Driver.

    You can find the USB Host controller entry in either of the following locations:
    • Universal Serial Bus Controllers.
    • Other Devices

      Note In the Other Devices location, the USB Host controller entry is labeled Universal Serial Bus controller with a yellow exclamation mark.
  4. Click Install the software automatically (Recommended), and then click Next.
  5. Click Finish when installation is finished.

    Note You may receive a message to restart your computer to finish the installation.
Back to the top

How to confirm driver versions

Make sure that you have the latest USB 2.0 drivers that are available in Windows XP Service Pack 1. You can do this by verifying your driver version in the following table:
Collapse this tableExpand this table
DateVersionFile name
29-Aug-20025.1.2600.1106 or later versionsUsbport.sys
29-Aug-20025.1.2600.1106 or later versionsUsbhub.sys
29-Aug-20025.1.2600.1106 or later versionsHccoin.dll
29-Aug-20025.1.2600.1106 or later versionsUsbehci.sys
Note When you install the USB 2.0 drivers from Windows XP Service Pack 1, this overwrites any third-party vendor provided USB 2.0 driver stacks for your PCI add-in cards. We recommend that you remove these driver stacks before you install the Windows XP Service Pack 1 USB 2.0 drivers.
Back to the top

Advanced information

USB 2.0 is a specification revision of the original USB 1.1 specification. USB 2.0 was approved April 2000. The corresponding EHCI specification was finished March 2002.

Windows XP did not include support for USB 2.0 technology for the following reasons:
  • There were no production quality EHCI 1.0 compatible host controllers.
  • There were not enough production-quality USB 2.0 devices for testing.
The Windows XP Service Pack 1 installer is designed to update all drivers and all files that are included with Windows XP. Because USB 2.0 drivers are not included with Windows XP, you must follow the steps in this article to obtain the latest drivers after you install Windows XP Service Pack 1.
Back to the top

REFERENCES

For more information about the most current articles that describe USBs, visit the following Microsoft Web site:
http://www.microsoft.com/whdc/connect/usb/default.mspx (http://www.microsoft.com/whdc/connect/usb/default.mspx)
Back to the top
APPLIES TO
  • Microsoft Windows XP Professional SP1
  • Microsoft Windows XP Home Edition SP1
Back to the top
Keywords: 
kbhowto kbenv kbinfo kbusb KB329632
Back to the top