This article describes how to connect a computer that is running either the Microsoft Windows Server 2003 Routing and Remote Access service or Internet Security and Acceleration (ISA) Server 2006 or ISA Server 2004 to a cable/DSL router and to access the Internet for browsing and e-mail for all clients on your local area network (LAN). If you use a DSL router, you do not have to use a Point to Point Protocol over Ethernet (PPPoE) driver on all Windows clients and on the Windows 2003-based server. In this environment, you have to make sure that you are using the correct routing configuration on both the DSL router and the server that is running either Routing and Remote Access or ISA Server. The DSL router has to know about all networks that are behind the Windows 2003-based server to be able to return all answers to the client's LAN.

Back to the top

The following configuration is an example of a network and an IP configuration:

Internet |--| IP-address_from_ISP - DSL_Router - 192.168.1.1 |--| 192.168.1.2 - Windows_Server_2003 - 192.168.168.249 |--| Hub_or_switch |--| Clients

This configuration uses the following settings:

•	DSL router IP address: 192.168.1.1 Subnet Mask: 255.255.255.0
•	Windows 2003-based server DSL network adapter IP address: 192.168.1.2 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 LAN network adapter IP address: 192.168.168.249 Subnet Mask: 255.255.255.0 The default gateway of the DSL network adapter (external network) points to the IP address of the DSL router.
•	Client workstation LAN network adapter IP address: 192.168.168.10 Subnet Mask: 255.255.255.0, Gateway: 192.168.168.249

To create the scenario that is described in the "Summary" section of this article, set the default gateway of all clients to the IP address of the LAN network adapter of the Windows 2003-based server. Set the DNS server entry on all network adapters to the IP address of the ISP's DNS server or to the IP address of the DSL router if it is configured as a DNS server.

If you experience connectivity issues on clients, check the routing table on the DSL router. You can access most devices by using an HTTP Web page (such as http://192.168.0.1). If the route is not present, add a static route to the client's network. To do so, use the following settings:



ISA Server has a built-in routing functionality. For more information about this functionality, see the Microsoft ISA Server Help. For additional information about the correct setting for internal and external network adapters and the Local Address Table (LAT), click the following article number to view the article in the Microsoft Knowledge Base:

Back to the top

Useful hints

•	Make sure that you are using the latest firmware updates for your DSL router.
•	Most DSL devices have to be restarted after you make a configuration change. After you restart the device, the switching table is rebuilt if the router has a built-in switch technology.
•	Review the documentation of your DSL router. If you do not have the manuals, see the manufacturer's Web site. For information about how to contact the manufacturer of your router, click the appropriate article number in the following list to view the article in the Microsoft Knowledge Base: 65416 (http://support.microsoft.com/kb/65416/) Hardware and Software Third-Party Vendor Contact List, A-K 60781 (http://support.microsoft.com/kb/60781/) Hardware and Software Third-Party Vendor Contact List, L-P 60782 (http://support.microsoft.com/kb/60782/) Hardware and Software Third-Party Vendor Contact List, Q-Z

•	If you use a virtual private network (VPN), the router must be able to handle two VPN connections at the same time. However, some routers cannot handle two VPN tunnels at the same time.
•	A router and firewall must be able to pass TCP port 1723 (Point-to-Point Tunneling Protocol [PPTP]) and Generic Route Encapsulation (GRE) protocol 47 for PPTP traffic to connect correctly. When a cable or DSL router cannot map GRE protocol 47 to the Routing and Remote Access server, you cannot connect to the server from the Internet. To resolve this issue, set the Routing and Remote Access server to "DMZ host" mode in the DSL router configuration and configure it to pass TCP port 1723 (for PPTP/VPN). Alternatively, you can let the router pass all requests using network address translation (NAT) with IP address translation, but without TCP port translation, and then assign a public address to the external network adapter of the Routing and Remote Access server. For additional information about this issue, click the following article number to view the article in the Microsoft Knowledge Base: 323441 (http://support.microsoft.com/kb/323441/) How to install and configure a Virtual Private Network Server in Windows Server 2003
•	If you use a DSL router that is configured for NAT, you must configure it to pass TCP port 25 traffic to receive e-mail messages from the Internet. TCP port 80 is used for Web browsing.
•	If you experience connectivity problems to the Internet on a computer that is running Microsoft Windows XP, make sure that Quality of Service (QoS) Packet Scheduler is running on the Windows XP client.

Back to the top

How to configure a Linksys BEFSR41 four-port cable/DSL router to route PPTP traffic to a Windows Server 2003-based VPN server

•	Open Advanced Features for the router, and then open Port Forwarding. For more information about how to perform this step, see the user manual for the router.
•	Set port 47 and port 1723 to the specified computer's IP address. Make sure that you have the latest firmware version.
•	Configure the perimeter network (also known as DMZ, demilitarized zone, and screened subnet) host IP address (that is, the internal IP address of the PPTP server).

Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
The third-party products that are discussed in this article are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, regarding the performance or reliability of these products.

Back to the top

For additional information, click the following article numbers to view the articles in the Microsoft Knowledge Base:

Back to the top