Article ID: 952607 - View products that this article applies to.
When you try to use a non-Microsoft Global Positioning System (GPS) device, or when you try to use the GPS functionality in Microsoft Streets & Trips, Microsoft MapPoint, or Microsoft AutoRoute, the device may be not detected, or the device may not work as it should.
This article describes how to troubleshoot issues that may occur when you try to use a third-party GPS device together with Streets & Trips, MapPoint, or AutoRoute. Additionally, the article describes specific devices that may require specific configuration.
Many GPS devices are available. Some of these devices may require you to perform additional troubleshooting steps to configure them and to them make work with Streets & Trips. If the following methods do not resolve the issue in which the GPS device is not detected in Streets & Trips, contact your GPS device manufacturer to determine other configuration steps that may be required.
Note Microsoft Customer Support Services will try to help you configure the device. However, if the device still cannot be detected after you use the following troubleshooting steps, the device may not work with Streets & Trips. Or, you may have to contact the device manufacturer for help with troubleshooting and configuring the device.
How Streets & Trips works with a third-party GPS USB deviceMost GPS device manufacturers support a standard protocol interface called "NMEA 0183 Interface Standard." This protocol was defined by the National Marine Electronics Association (NMEA).
The NMEA 0183 protocol is an intermediate driver that enables a software program to communicate with a GPS device. The NMEA 0183 protocol holds information about the position, the satellite status, and any other navigation status. However, not all GPS devices use the NMEA 0183 protocol.
A USB device can support multiple connections. You can also connect several USB devices together and then connect the devices to one USB port. The USB standard has its own protocols for connections. However, the USB standard does not include support for GPS devices.
Streets & Trips recognizes only devices that are connected through a serial port. Therefore, to emulate a serial port, a GPS device manufacturer must create a driver by using a proprietary interface. The driver makes the computer respond as if the USB device is being accessed through a serial port. In effect, the driver creates a virtual serial port connection. This driver is required not only for Streets & Trips but also for other mapping software.
If the GPS device manufacturer does not provide drivers, third-party software may provide a solution. An example of such software is Franson GpsGate.
For example, when GpsGate is connected to a Garmin USB GPS device, the Garmin GPS device appears as an ordinary NMEA GPS device that is connected to a serial port. You can connect any number of GPS applications to the GPS device at the same time.
For more information, visit the following Web site:
http://franson.com/gpsgate/Streets & Trips Standard and Streets & Trips with GPS Locator work together with the Pharos GPS device. This device includes specific Pharos drivers that were created to work with Streets & Trips.
For more information about Streets & Trips with GPS Locator, visit the following Microsoft Web site:
How to troubleshoot the issue when the GPS device is not detected in Streets & Trips
Method 1: Verify NMEA 0183 complianceMake sure that the device that you are trying to use is compatible with Streets & Trips. To work with Streets & Trips, the GPS device must be compliant with NMEA standards, and its input/output format (also known as the interface) must be set to support NMEA 0183 version 2.0 or a later version of the NMEA 0183 format.
For more information about how to determine whether your GPS device is NMEA-complaint, see the documentation that was included with your device, contact the GPS device manufacturer, or visit the following Web site:
Method 2: Use Device ManagerStreets & Trips recognizes devices that are connected through COM ports. The GPS driver that is included with the GPS device must be able to convert the USB port to a COM port through emulation. When the driver does this, it makes Streets & Trips respond as if the GPS device is connected through a COM port.
If Device Manager recognizes the GPS device but Streets & Trips does not, it is likely that the device’s driver is not converting the USB connection to a COM port connection. In this case, contact the GPS device manufacturer for additional troubleshooting.
To resolve the issue by using Device Manager, follow these steps:
How to troubleshoot hardware-specific GPS device issuesIf the GPS device is still not detected after you use the methods that are described in the previous section and if your device was manufactured by a manufacturer other than Garmin or DeLorme, contact the GPS device manufacturer.
If the device was manufactured by Garmin or DeLorme, see the following sections.
GarminNot all Garmin devices support the NMEA 0183 Interface Standard.
Garmin GPS devices are frequently connected to the computer by using the USB cable that is supplied with the device. The USB cable is compliant with and transmits only the proprietary Garmin signals. This condition makes the devices compatible only with Garmin software such as Map Source and nRoute.
The USB version of Garmin GPS devices does not support NMEA 0183. This version supports only Garmin's own protocol. Therefore, very few GPS applications can use Garmin USB GPS devices.
If Franson GpsGate does not work, contact Garmin technical support. To do this, visit the following Web site:
DeLormeWhen you try to use a DeLorme GPS device together with AutoRoute, MapPoint, or Streets & Trips, you cannot select the DeLorme GPS device. This issue occurs even though the device is working in the DeLorme Street Atlas program or in Microsoft HyperTerminal.
The affected DeLorme devices include the USB Earthmate GPS, Earthmate GPS BT-20, Earthmate GPS LT series, or Earthmate GPS PN series devices, among others.
To work around this issue, install the DeLorme USB-to-serial driver by using the DeLorme driver disk. To do this, follow these steps:
For more information about how to submit feedback, click the following article number to view the article in the Microsoft Knowledge Base:
281826For more information about how to troubleshoot issues that may occur with Microsoft GPS devices, click the following article number to view the article in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/281826/ )How to submit feedback to Microsoft about the map data in Autoroute, in MapPoint, or in Streets and Trips
894511For more information about NMEA, visit the following NMEA Web site:
(http://support.microsoft.com/kb/894511/ )How to troubleshoot Microsoft GPS device with Microsoft Streets and Trips
http://www.nmea.orgThe third-party products that this article discusses are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, about the performance or reliability of these products.
Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Article ID: 952607 - Last Review: April 9, 2013 - Revision: 5.0
Contact us for more help