A delay occurs when you try to reconnect to the network on a Windows Vista Service Pack 1-based or Windows Server 2008-based computer that is a member of a domain

You have a Windows Vista Service Pack 1 (SP1)-based or Windows Server 2008-based computer that is a member of a domain. When you disconnect from the network, you may experience a delay of 12 to 14 seconds before you can access the network again.

Notes

• This issue usually occurs when the computer switches between a network that deploys Network Access Protection (NAP) enforcement and another network.
• This issue does not occur on a computer that is running the release version of Windows Vista or on a computer that is not a domain member.

This issue occurs because the Dynamic Host Configuration Protocol (DHCP) client sends ARP packets from Windows Networking Services.

When a client disconnects and then reconnects to a network, the client sends a new DHCP REQUEST packet. If the DHCP client belongs to a new subnet, the server responds to the client by using a DHCP negative acknowledgement (NAK) packet. Therefore, the client sends an address resolution protocol (ARP) request for the previously configured default gateway. However, no reply is received. Finally, after waiting 12 to 14 seconds, the client sends a DHCP DISCOVER packet. This packet starts a full renewal of the address.

Hotfix information for Windows Vista and Windows Server 2008

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that is described in this article. Apply this hotfix only to systems that are experiencing this specific problem. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.

If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.

Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft Web site: Note The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.

Important Windows Vista and Windows Server 2008 hotfixes are included in the same packages. However, only one of these products may be listed on the “Hotfix Request” page. To request the hotfix package that applies to both Windows Vista and Windows Server 2008, just select the product that is listed on the page.

Prerequisites

To apply this hotfix, you must have Windows Vista SP1 or Windows Server 2008 installed on the computer.

Restart requirement

You have to restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace any other previously released hotfixes.

Registry information

To use this hotfix, you do not have to make any changes to the registry.

File information

The English version of this hotfix has the file attributes (or later file attributes) that are listed in the following table. The dates and times for these files are listed in Coordinated Universal Time (UTC). When you view the file information, it is converted to local time. To find the difference between UTC and local time, use the Time Zone tab in the Date and Time item in Control Panel.

Windows Server 2008 and Windows Vista file information notes

The .manifest files and the .mum files that are installed in each environment are listed separately in the "Additional file information for Windows Server 2008 and for Windows Vista" section. These files and their associated .cat (security catalog) files are critical to maintaining the state of the updated component. The .cat files are signed with a Microsoft digital signature. The attributes of these security files are not listed.

For all supported x86-based versions of Windows Server 2008 and Windows Vista

For all supported x64-based versions of Windows Server 2008 and Windows Vista

For all supported Itanium-based versions of Windows Server 2008

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

For more information, click the following article number to view the article in the Microsoft Knowledge Base:

Additional file information for Windows Vista and for Windows Server 2008

Additional files for all supported x86-based versions of Windows Vista and Windows Server 2008

Additional files for all supported x64-based versions of Windows Vista and Windows Server 2008

Additional files for all supported Itanium-based versions of Windows Server 2008