Article ID: 976386 - View products that this article applies to.
RAPID PUBLISHING ARTICLES PROVIDE INFORMATION DIRECTLY FROM WITHIN THE MICROSOFT SUPPORT ORGANIZATION. THE INFORMATION CONTAINED HEREIN IS CREATED IN RESPONSE TO EMERGING OR UNIQUE TOPICS, OR IS INTENDED SUPPLEMENT OTHER KNOWLEDGE BASE INFORMATION.
When you try to start a Windows Vista or Windows Server 2008-based computer after installing a Windows Service Pack and subsequently uninstalling NetGear Storage Central or Zetera Z-SAN software, you receive the following stop error message:
STOP: 0x0000007B ( parameter1 , parameter2 , parameter3 , parameter4 )
This problem may occur under the following conditions: You have the NetGear Storage Central software, including the Zetera Z-SAN drivers, installed on a computer running Windows Vista or Windows Server 2008.You perform either an in-place-upgrade of your existing Windows Vista or Windows Server 2008 operating system, or install a Windows Vista or Windows Server 2008 Service Pack.You uninstall the NetGear Storage Central software or the Zetera Z-SAN drivers.You restart Windows.
Under these conditions, the registry entries to load the Zetera ZetSFD.sys filter driver may be migrated from the Disk Class registry subkey to the registry subkeys for specific Disk Class devices by the Windows Vista or Windows Server 2008 setup program. When the Zetera software is subsequently uninstalled, the driver files themselves are deleted, but the registry entries to load the Zetera ZetSFD.sys filter driver are not removed from the registry by the Zetera setup/uninstall program. As a result, when Windows restarts, the system attempts to load these filter drivers that are no longer present on the system. If this failure to load required drivers occurs for the disk device on which Windows is installed, Windows will be unable to access the disk, and thus unable to continue starting.
To allow the NetGear Storage Central or Zetera Z-SAN software to be safely uninstalled after installing a Windows Service Pack or performing an in-place upgrade installation of Windows Vista or Windows Server 2008, perform the following actions:
If you have already installed a Windows Service Pack or performed an in-place upgrade installation of Windows Vista or Windows Server 2008, you may safely uninstall the NetGear Storage Central and/or Zetera Z-SAN software by performing the following actions:
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/322756)How to back up and restore the registry in Windows
For information on similiar issues, see the following articles in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/940267)You receive an error message if you try to install a USB device on a Windows Vista-based computer that was upgraded from Windows XP
For information on Windows Vista Setup Filter Driver Migration behavior, see the following articles in the Microsoft Knowledge Base:
(http://support.microsoft.com/kb/976267)Filter Driver Registry Entries Are Migrated During Windows Vista or Windows Server 2008 Upgrade or Service Pack Setup
MICROSOFT AND/OR ITS SUPPLIERS MAKE NO REPRESENTATIONS OR WARRANTIES ABOUT THE SUITABILITY, RELIABILITY OR ACCURACY OF THE INFORMATION CONTAINED IN THE DOCUMENTS AND RELATED GRAPHICS PUBLISHED ON THIS WEBSITE (THE “MATERIALS”) FOR ANY PURPOSE. THE MATERIALS MAY INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS AND MAY BE REVISED AT ANY TIME WITHOUT NOTICE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, MICROSOFT AND/OR ITS SUPPLIERS DISCLAIM AND EXCLUDE ALL REPRESENTATIONS, WARRANTIES, AND CONDITIONS WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO REPRESENTATIONS, WARRANTIES, OR CONDITIONS OF TITLE, NON INFRINGEMENT, SATISFACTORY CONDITION OR QUALITY, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE MATERIALS.
Article ID: 976386 - Last Review: October 7, 2009 - Revision: 1.0
Contact us for more help
Connect with Answer Desk for expert help.