This article describes the Microsoft support policy for server clusters, the Hardware Compatibility List (HCL), and the Windows Server Catalog (WSC). Microsoft Product Support Services (PSS) supports only server clusters on hardware that is listed on the Cluster HCL for Windows 2000 Server and Windows NT server, or on the Cluster WSC for Windows 2003 Server. In this context, "server clusters" refers to computers that run the Microsoft Cluster service, not Network Load Balancing (NLB) or Windows Load Balancing Service (WLBS).
To view the most current Windows Server 2000 and Windows Server 2003 Cluster Solutions list, visit the following Microsoft Web site:
When you visit this Web site, click Cluster Solutions in the hardware testing status section. To search by components of a cluster solution, use any of the three search boxes available in the left navigation pane of the Cluster Solutions page. Type a product or vendor name in any of the search boxes to view cluster solutions that contain the product name or vendor name that you are searching for. Search results can then be filtered by OS compatibility, by vendor name, and by processor architecture. To filter the search results by category, such as geographically dispersed cluster solutions, use the category filter.
Note When you click any of the arrows next to the search boxes in the left navigation pane, the search boxes will simultaneously filter the results by the text that you typed in all the search boxes.
Windows Server 2008 Cluster solutions will not be listed in the Windows Server Catalog.For more information, visit the following Failover Clustering Configuration Program Web site:
Customers should not use this list to build a cluster solution because using these individual components in a cluster does not qualify as a complete HCL or WSC solution. PSS fully supports only clusters that are complete solutions that are listed in the Cluster category on the HCL or WSC.
A typical HCL or WSC-compliant cluster contains the following components:
Two or more servers that are referred to as the cluster nodes.
A mass-storage controller and drives in each node from which the operating system boots.
A separate mass-storage controller (SCSI or Fibre) that is independent of the controller that is used to boot the operating system.
The shared disk. This is typically an external cabinet to which the mass-storage controller is attached that is connected to all nodes in the cluster.
Two network adapters in each cluster node.
Note that adaptations of server clusters from OEMs may contain variations on these components, may not contain all of the components, or may contain more of the components that are listed. The key, however, to Microsoft support is that the entire cluster is listed on the HCL or WSC in the Cluster category.
However, there may still be configuration issues with an HCL-compliant or a WSC-compliant cluster. Therefore, we recommend that you run the Microsoft Cluster Configuration Validation Wizard to determine any potential configuration problems before you configure a Windows 2000 server cluster or a Microsoft Windows Server 2003 server cluster. To download the Microsoft Cluster Configuration Validation Wizard, visit the following Microsoft Web site:
When you configure a Windows NT 4.0-based server cluster, the cluster installation routine displays the following agreement:
Microsoft Cluster Server (MSCS) is only supported if it is installed on a hardware configuration that has been tested for compatibility with the MSCS software.
Press I Agree to accept these conditions.
The Cluster Setup program in Windows 2000 displays the following agreement:
Your hardware configuration must be tested for compatibility with the Cluster service.
Microsoft does not support hardware configurations other than those listed in the Cluster category of the Hardware Compatibility List (HCL) located at
To indicate that you understand that Microsoft does not support hardware configurations that are not listed in the Cluster category of the HCL, click I Understand.
Windows Server 2003 does not display a dialog box that prompts for acceptance of the HCL or WSC agreement during the cluster configuration. The requirements for the Cluster service do state that an HCL cluster is required.
SAN, Geographically dispersed clusters, and Windows 2000 Datacenter Server
If multiple clusters are attached to the same storage area network (SAN) device, extra steps are required. The nodes in the cluster must be certified with the particular SAN device. The SAN device itself must be certified as Multi-Cluster capable and listed in the Cluster/Multi-Cluster Device category.
If the cluster solution includes geographically dispersed cluster nodes, additional items such as network latency and shared disk support must be verified. The entire cluster solution must be listed in the Cluster/Geographic category. See the following Microsoft Knowledge Base article for details:
280743 Windows clustering and geographically separate sites
Server clusters that run on Windows 2000 Datacenter Server have additional requirements for support. There may be certain contractual limitations to which you must adhere. See the following Microsoft Knowledge Base article for details:
265173 The Datacenter program and Windows 2000 Datacenter Server product
Clusters that are not listed on the HCL in the cluster category
If your cluster solution is not listed on the HCL or WSC in the Cluster category, the cluster solution is considered unsupported. However, PSS will offer troubleshooting tips if the customer requests them. PSS does not guarantee that a resolution will be found for non-HCL or non-WSC Clusters.
Steps for support
Before any troubleshooting begins, the customer must contact the OEM to discuss whether the particular cluster implementation is supportable. The OEM can best answer configuration and supportability questions for the cluster hardware.
Upon agreement that no solution is guaranteed, and that no incident refund will be given, PSS troubleshoots the issue. Microsoft does not guarantee a solution with non-HCL or non-WSC clusters. If no resolution is found, the incident is not refunded.
If it is not agreed that a solution is not guaranteed, PSS will not troubleshoot the issue and will refund the incident.
Standard troubleshooting processes will be used to isolate the server cluster issue. Some typical troubleshooting methods that will be used by PSS include:
The Microsoft Knowledge Base is available to customers through Microsoft TechNet and the following Microsoft Web site:
Determine whether the problem can be replicated on supported clusters (where possible).
Note If the cluster is not certified, there is no hotfix support available. PSS will be unable to determine whether the problem is caused by a hardware incompatibility or undesirable software behavior.
If there is no solution to the problem, PSS may recommend some constructive alternatives, including:
Having the customer reproduce the problem on a cluster that is on the Cluster HCL or WSC.
Using a cluster solution that is on the Cluster HCL or WSC.
Having the customer work with the OEM to get the cluster on the Cluster HCL or WSC.
Working with the OEM for a solution.
The hardware specifications for server clusters are extremely stringent. The Cluster HCL and WSC contains a list of known acceptable cluster configurations that have been tested. You can waste a lot of time by attempting to troubleshoot perceived server cluster issues that are being caused by the cluster hardware that you are using.
Some examples of hardware incompatibilities that can cause cluster problems include:
The cluster solution does not properly isolate the shared disk and HBAs from other devices on the shared bus.
The SCSI controller does not support operating in a multiple-initiator environment.
The HBA does not properly handle reservations or release or renew a device on the shared bus.
The caching mechanism on the controller is incompatible with the cluster configuration.
The network adapters for intra-cluster communication have too high a latency.
The RAID controller does not properly replicate configuration information between controllers.
The PCI bus is incorrectly configured and has incorrect adapters in the wrong bus (primary, secondary, tertiary, and so on).
The controllers are incompatible the "Physical Disk Resource" type.
The SCSI controller does not deploy proper termination.
This list does not include all the issues that can cause problems with a server cluster. None of these issues can be detected by PSS. All of these issues would typically be discovered if the complete cluster solution were tested for Cluster HCL or WSC compatibility.
If a complete cluster configuration is listed for an earlier operating system but is not listed for the newer operating system that you are using, support as documented in this section will be followed.
mscs hwtest clustering HBA host bus adapter hct reasonable effort
Microsoft Windows Server 2003, Enterprise Edition (32-bit x86), Microsoft Windows Server 2003, Datacenter Edition (32-bit x86), Microsoft Windows 2000 Advanced Server, Microsoft Windows NT Server 4.0 Enterprise Edition