The primary benefit of DEP is to help prevent code execution from data pages. Typically, code is not executed from the default heap and the stack. Hardware-enforced DEP detects code that is running from these locations and raises an exception when execution occurs. Software-enforced DEP can help prevent malicious code from taking advantage of exception-handling mechanisms in Windows.
Hardware-enforced DEP relies on processor hardware to mark memory with an attribute that indicates that code should not be executed from that memory. DEP functions on a per-virtual memory page basis, and DEP typically changes a bit in the page table entry (PTE) to mark the memory page.
Processor architecture determines how DEP is implemented in hardware and how DEP marks the virtual memory page. However, processors that support hardware-enforced DEP can raise an exception when code is executed from a page that is marked with the appropriate attribute set.
Advanced Micro Devices (AMD) and Intel have defined and shipped Windows-compatible architectures that are compatible with DEP.
Beginning with Windows XP SP2, the 32-bit version of Windows uses one of the following:
- The no-execute page-protection (NX) processor feature as defined by AMD.
- The Execute Disable Bit (XD) feature as defined by Intel.
Note Because 64-bit kernels are Address Windowing Extensions (AWE) aware, there is not a separate PAE kernel in 64-bit versions of Windows.
For more information about PAE and AWE in Windows Server 2003, click the following article number to view the article in the Microsoft Knowledge Base:
back to top
DEP can help block a class of security intrusions. Specifically, DEP can help block a malicious program in which a virus or other type of attack has injected a process with additional code and then tries to run the injected code. On a system with DEP, execution of the injected code causes an exception. Software-enforced DEP can help block programs that take advantage of exception-handling mechanisms in Windows.
back to top
Windows supports four system-wide configurations for both hardware-enforced and software-enforced DEP.
|OptIn||This setting is the default configuration. On systems with processors that can implement hardware-enforced DEP, DEP is enabled by default for limited system binaries and programs that "opt-in." With this option, only Windows system binaries are covered by DEP by default.|
|OptOut||DEP is enabled by default for all processes. You can manually create a list of specific programs that do not have DEP applied by using the System dialog box in Control Panel. Information technology (IT) professionals can use the Application Compatibility Toolkit to "opt-out" one or more programs from DEP protection. System compatibility fixes, or shims, for DEP do take effect.|
|AlwaysOn||This setting provides full DEP coverage for the whole system. All processes always run with DEP applied. The exceptions list to exempt specific programs from DEP protection is not available. System compatibility fixes for DEP do not take effect. Programs that have been opted-out by using the Application Compatibility Toolkit run with DEP applied.|
|AlwaysOff||This setting does not provide any DEP coverage for any part of the system, regardless of hardware DEP support. The processor does not run in PAE mode unless the /PAE option is present in the Boot.ini file.|
Similarly, if the system-wide DEP policy is set to OptOut, programs that have been exempted from DEP protection will be exempted from both hardware-enforced and software-enforced DEP.
The Boot.ini file settings are as follows:
Existing /noexecute settings in the Boot.ini file are not changed when Windows XP SP2 is installed. These settings are also not changed if a Windows operating system image is moved across computers with or without hardware-enforced DEP support.
During installation of Windows XP SP2 and Windows Server 2003 SP1 or later versions, the OptIn policy level is enabled by default unless a different policy level is specified in an unattended installation. If the /noexecute=policy_level setting is not present in the Boot.ini file for a version of Windows that supports DEP, the behavior is the same as if the /noexecute=OptIn setting was included.
If you are logged on as an administrator, you can manually configure DEP to switch between the OptIn and OptOut policies by using the Data Execution Prevention tab in
System Properties. The following procedure describes how to manually configure DEP on the computer:
- Click Start, click Run, type sysdm.cpl, and then click
- On the Advanced tab, under
Performance, click Settings.
- On the Data Execution Prevention tab, use one of the following procedures:
- Click Turn on DEP for essential Windows programs and services only to select the OptIn policy.
- Click Turn on DEP for all programs and services except those I select to select the OptOut policy, and then click
Add to add the programs that you do not want to use the DEP feature.
- Click OK two times.
To configure DEP to switch to the AlwaysOn policy by using the Boot.ini file, follow these steps:
- Click Start, right-click My Computer, and then click Properties.
- Click the Advanced tab, and then click Settings under the Startup and Recovery field.
- In the System startup field, click Edit. The Boot.ini file opens in Notepad.
- In Notepad, click Find on the Edit menu.
- In the Find what box, type /noexecute, and then click Find Next.
- In the Find dialog box, click Cancel.
- Replace policy_level with AlwaysOn.
WARNING Make sure that you enter the text accurately. The Boot.ini file switch should now read:/noexecute=AlwaysOn
- In Notepad, click Save on the File menu.
- Click OK two times.
- Restart the computer.
back to top
System Properties to selectively disable DEP for a program. For IT professionals, a new program compatibility fix that is named DisableNX is included with Windows XP SP2. The DisableNX compatibility fix disables Data Execution Prevention for the program that the fix is applied to.
The DisableNX compatibility fix can be applied to a program by using the Application Compatibility Toolkit. For more information about Windows application compatibility, see Windows Application Compatibility on the following Microsoft Web site:back to top
Article ID: 875352 - Last Review: 28 Jun 2017 - Revision: 5