MS-DOS 6.22 SCANDISK.INI File

This article was previously published under Q116397
This article has been archived. It is offered "as is" and will no longer be updated.
Summary
This article contains a complete listing of the MS-DOS 6.22 SCANDISK.INIfile.
More information
; SCANDISK.INI;; This file contains settings you can use to customize the ScanDisk; program.; -------------------------------------------------------------------; The [ENVIRONMENT] section contains the following settings, which; determine general aspects of ScanDisk's behavior:;; Display      Configures ScanDisk to run with a particular type of;              display. The default display type is Auto (ScanDisk;              adjusts to the current display).;; Mouse        Enables or disables mouse support. The default value is On.;; ScanTimeOut  Determines whether ScanDisk should detect disk timeouts;              while performing a surface scan. The default value is Off.;; NumPasses    Determines how many times ScanDisk should check each;              cluster during a surface scan. The default value is 1.;; LabelCheck   Determines whether ScanDisk should check volume labels;              for invalid characters. The default is Off.;; LfnCheck     Enables support for long filenames. The default value is On.;              If LfnCheck is On, ScanDisk leaves any long filenames;              unchanged. If LfnCheck is Off, ScanDisk validates;              all filenames, including long filenames, to ensure that;              they conform to the "8.3" file-naming convention used by;              MS-DOS versions 6.22 and earlier.;[ENVIRONMENT]   Display     = Auto   ; Auto, Mono, Color, Off   Mouse       = On     ; On, Off   ScanTimeOut = Off    ; On, Off   NumPasses   = 1      ; 1 through 65,535 (anything over 10 is slow)   LabelCheck  = Off    ; On, Off   LfnCheck    = On     ; On, Off; -------------------------------------------------------------------; The [CUSTOM] section determines ScanDisk's behavior when ScanDisk is; started with the /CUSTOM switch. You can adjust these settings to; create a customized "version" of ScanDisk. This can be especially; useful for running ScanDisk from a batch file. The [CUSTOM] settings are:;; DriveSummary  Determines whether ScanDisk displays full-screen;               summary information after checking each drive.;               The default is Auto (ScanDisk displays the summary;               only if it encounters errors on that drive).;; AllSummary    Determines whether ScanDisk displays full-screen;               summary information after checking all drives.;               The default is Auto (ScanDisk displays the summary;               only if it encounters errors on any drive).;; Surface       Determines whether ScanDisk will perform a surface scan:;                  Never    (Default) Does not perform a surface scan.;                  Always   Performs a surface scan without prompting;                           first.;                  Prompt   Prompts before performing a surface scan.;               The /SURFACE command-line switch overrides this setting.;; CheckHost     Determines whether ScanDisk will first check a host drive;               before checking any compressed drives located on that;               drive.;                  Never    (Default) Does not check the host drive.;                  Always   Checks the host drive without prompting first.;                  Prompt   Prompts before checking the host drive.;; SaveLog       Determines what ScanDisk does with the repair log file:;                  Off        (Default) Does not save the repair log.;                  Append     Appends the log to the previous log, if any.;                  Overwrite  Replaces the previous log with the new log.;; Undo          Determines whether ScanDisk creates an Undo floppy disk.;               The default is Never (ScanDisk does not create an Undo;               disk).;               The Prompt value causes ScanDisk to prompt you for a disk.[CUSTOM]   DriveSummary  = Auto         ; Auto, On, Off   AllSummary    = Auto         ; Auto, On, Off   Surface       = Never        ; Never, Always, Prompt   CheckHost     = Never        ; Never, Always, Prompt   SaveLog       = Off          ; Off, Append, Overwrite   Undo          = Prompt       ; Prompt, Never; The following settings determine the corrective action ScanDisk will; take if it was started with the /CUSTOM switch and finds a disk error.; The next five settings accept any of the following values:;    Prompt     Causes ScanDisk to prompt you before fixing this problem.;    Fix        Causes ScanDisk to fix the problem without prompting you.;    Quit       Causes ScanDisk to terminate if it encounters this problem.   DS_Header     = Prompt       ; Damaged compressed volume file header   FAT_Media     = Prompt       ; Missing or invalid FAT media byte   Okay_Entries  = Prompt       ; Damaged, but repairable,                                ; directories/files   Bad_Chain     = Prompt       ; Files or directories which should be                                ; truncated   Crosslinks    = Prompt       ; FAT-level crosslinks; The next seven settings accept any of the following values:;    Prompt     Causes ScanDisk to prompt you before fixing this problem.;    Fix        Causes ScanDisk to fix the problem without prompting you.;    Quit       Causes ScanDisk to terminate if it encounters this problem.;    Skip       Causes ScanDisk to skip fixing this problem, but continue;               checking the disk.   Boot_Sector   = Prompt       ; Damaged boot sector on compressed drive   Invalid_MDFAT = Prompt       ; Invalid MDFAT entries   DS_Crosslinks = Prompt       ; Internal (MDFAT-level) crosslinks   DS_LostClust  = Prompt       ; Internal lost clusters   DS_Signatures = Prompt       ; Missing compressed volume file signatures   Mismatch_FAT  = Prompt       ; Mismatched FATs on non-compressed drives   Bad_Clusters  = Prompt       ; Physical damage or decompression errors; The next setting accepts any of the following values:;;    Prompt     Causes ScanDisk to prompt you before fixing this problem.;    Delete     Causes ScanDisk to delete the damaged directory entries;               without prompting you first.;    Quit       Causes ScanDisk to terminate if it encounters this problem.   Bad_Entries   = Prompt       ; Damaged and irreparable directories or                                ; files; The next setting accepts any of the following values:;;    Prompt     Causes ScanDisk to prompt you before fixing this problem.;    Save       Causes ScanDisk to save the lost clusters as files in the;               root directory without prompting you first.;    Delete     Causes ScanDisk to delete the contents of the lost clusters;               without prompting you first.;    Quit       Causes ScanDisk to terminate if it encounters this problem.;    Skip       Causes ScanDisk to skip fixing this problem, but continue;               checking the disk.   LostClust     = Prompt       ; Lost clusters				
6.22
Properties

Article ID: 116397 - Last Review: 10/26/2013 12:39:00 - Revision: 2.0

  • Microsoft MS-DOS 6.22 Standard Edition
  • kbnosurvey kbarchive KB116397
Feedback