Troubleshooting Floppy Disk Drive Problems in Windows

This article was previously published under Q131690
This article has been archived. It is offered "as is" and will no longer be updated.
If this article does not describe your hardware-related issue, please see the following Microsoft Web site to view more articles about hardware:
SUMMARY
This article lists troubleshooting tips you can use to help resolveproblems with floppy disk drives in Windows.
MORE INFORMATION
If you are having problems with a floppy disk drive (such as receiving theerror message "Error reading drive <X>:" or if the status of your floppy disk drive in Device Manager is listed in MS-DOS Compatibility mode), try the troubleshooting tips in the following sections.

Safe Mode

Start Windows in Safe mode and try to access the floppy disk drive. Tostart Windows 95 in Safe mode, restart your computer, press the F8 keywhen you see the "Starting Windows 95" message, and then choose Safe Modefrom the Startup menu. To start Windows 98 in Safe mode, restart yourcomputer, press and hold down the CTRL key after your computer completesthe Power On Self Test (POST), and then choose Safe Mode from the Startupmenu.

If you can access the floppy disk drive, follow these steps:

  1. Use the right mouse button to click My Computer, then click Properties on the menu that appears.
  2. Click the Device Manager tab.
  3. Double-click Floppy Disk Controllers.
  4. Click the floppy disk controller for the drive you are having problems with, then click Properties.
  5. In Windows 95, click the Original Configuration (Current) check box to clear it. In Windows 98, click the Disable In This Hardware Profile check box to select it. This disables the Windows protected-mode driver for the floppy disk drive controller.
  6. Click OK.
  7. Restart Windows normally.
If you can access the floppy disk drive successfully after following theabove steps, the following conditions may be true:
  • The floppy disk drive controller may not be supported in protected mode.
  • There are drivers loading in the Config.sys or AUTOEXEC.BAT file that may be necessary for protected-mode access.
  • There are drivers loading in the CONFIG.SYS or AUTOEXEC.BAT file that may be causing conflicts in Windows and need to be disabled.
If you still cannot access the floppy disk drive after following steps1-7, follow these steps:
  1. Use the right mouse button to click My Computer, then click Properties on the menu that appears.
  2. Click the Device Manager tab.
  3. Double-click Floppy Disk Controllers.
  4. Click the floppy disk controller, and then click Remove to remove the controller.
  5. Click OK.
  6. In Control Panel, double-click Add New Hardware.
  7. Click Next, and then click Yes to allow Windows to detect the hardware in your computer.
  8. When the Add New Hardware Wizard is finished, restart the computer and try to access the floppy disk drive again.
Redetecting the floppy disk controller should resolve any addressingproblems with the controller by detecting the correct address range. Ifthe floppy disk controller is not detected correctly, there may be aproblem with the floppy disk controller. If the floppy disk controller isredetected but you still cannot access the floppy disk drive, there may bea problem with the floppy disk.

Damaged Disks

Use the following steps to check for a damaged disk:
  1. Use a disk utility (such as ScanDisk) to test the disk for damage.

    NOTE: Do not use a non-Windows 95 or Windows 98-aware disk utility on DMF disks. Non-Windows 95 or Windows 98-aware disk utilities can damage DMF disks. The Windows ScanDisk tool recognizes and does not damage DMF disks.

    Before you run a disk utility, please see the following article in the Microsoft Knowledge Base:
    ARTICLE-ID: 120442
    TITLE : Using Hard Disk Utilities with Windows 95
  2. Type the following command at an MS-DOS command prompt

    copy drive\*.* nul

    where <drive> is the floppy disk drive you are having problems with. For example, if you are having problems with drive A, insert a disk you are having problems with in drive A and type the following command:

    copy a:\*.* nul

    This command copies the files on the disk to a null device. If there is a problem copying the files, error messages appear on the screen.


CMOS Settings

Consult your computer's documentation or manufacturer to make sure thatyour computer's CMOS settings are correct.

Irwin Tape Backup

Windows 95 Setup removes the following statement from the [386Enh] sectionof the SYSTEM.INI file:
   device=<path>\VIRWT.386				

If you re-install the Irwin Tape Backup software after you install Windows95, this statement is placed in the SYSTEM.INI file again and can causeconflicts with floppy disk access in Windows.


Device Conflicts

Device conflicts as reported by Device Manager can cause problems readingfrom and writing to floppy disks. You can resolve this problem by changingor removing the resources from Device Manager that are causing theconflict. These are typically conflicts with hard drive controller cards,video cards, or COM ports.

HWFDCTL clean boot ms-dos compatibility w95hwfaq
Properties

Article ID: 131690 - Last Review: 12/04/2015 11:31:29 - Revision: 2.2

Microsoft Windows 95, Microsoft Windows 98 Standard Edition, Microsoft Windows 98 Second Edition, Microsoft Windows 98 Standard Edition

  • kbnosurvey kbarchive kbenv kbfaq kbhardware kbhowto kbtshoot KB131690
Feedback