Troubleshooting MacVolume Creation Errors

This article was previously published under Q147909
This article has been archived. It is offered "as is" and will no longer be updated.
When you use Services for Macintosh (SFM) for Windows NT, there may beoccasional issues creating or re-creating a MacVolume. The followingerror message may appear when you create the volume:
The Device attached to the system is not functioning
In the event log, the following error message is displayed:
Event ID: 12035
Description: Volume information for volume name could not be loaded.
Setting defaults.
The following methods should be tried individually and in sequential order.Before each step, stop Services for Macintosh (SFM) in the Services tool inControl Panel. Before you continue with the next step, restart SFM and testfor success by attempting to re-create the volume on the preferreddirectory.

Method 1

Run Chkdsk.exe with the /f and /r command-line switches on the partition that is generating the error message. Running Chkdsk.exe usually requires restarting the server. If the volume is large in size, it may take several minutes to several hours to complete and the server may not be available during this time. If time is a concern and you have a large volume, skip this method and continue to method 2. At some point when time permits, run Chkdsk.exe on the server.

Method 2

Create a temporary Macintosh volume on a new partition. Copy all files and folders from the original Macintosh volume into the temporary volume on the new partition.

NOTE: Existing Macintosh NTFS file system (NTFS) permissions are not retained. You can use Scopy.exe, which can be found in the Windows NT Resource Kit, to retain all file and folder permissions if necessary.

Remove the original Macintosh volume from MacFile. Delete the originalfolder, and then re-create the volume using the same volume name. Ifthis is successful, move all files and folders from the temporaryvolume back into the re-created volume.

Method 3

Create a temporary Macintosh volume. Move all files and folders fromthe original Macintosh volume into the temporary volume on the samedrive.

NOTE: This ensures that permissions are retained.

Remove the original Macintosh volume from MacFile, delete the originalfolder, and then re-create the volume using the same volume name. Ifthis is successful, move all files and folders from the temporaryvolume back into the re-created volume.

Method 4

Remove the volume in question from Macfile, and then delete the Iconfile and Network trash folder. These files (Hidden/System) exist in theroot of the Macintosh volume (folder).

Method 5

If the issue exists in a volume that is part of a folder (forexample, D:\Public), type the following command at a commandprompt:
dir > d:\public:afp_idindex
If you are rebuilding a root drive share such as C:\ or D:\, type thefollowing command at a command prompt:
dir > d:\:afp_idindex
NOTE: This command intentionally damages the index of theMacintosh volume. After SFM is stopped and restarted, the damage forces Windows NT to rebuild the index on that volume immediately. If an "access denied" error message occurs, the volume may be in use by opened files or the folder is being shared for personal computer access. Disable all programs and file sharing to prevent this error message.

After SFM is restarted and the index is complete, an event is logged in Event Viewer. If the volume is large in size, it may take several minutes before all volumes and files are visible by the Macintosh client. Avoid stopping the SFM service at this time.

The following error will appear when you corrupt the volume index:
Event ID: 12042
Source: MacFile
Description: Internal server information for file "\<volume name>:AFP_AfpInfo" was corrupted.
Setting default information.

Method 6

Use Disk Administrator to change the drive letter of the partitionexhibiting the problem. For example, if drive D had the original Macintoshvolume, change it to drive E (as long as E is not being used by anotherdevice). Restart the computer running Windows NT and attempt to createthe volume. If this is successful, you can use Disk Administrator tochange back to the original drive letter.

NOTE: This procedure damages the NTFS data stream and forces MacFile to regenerate it. This step is only necessary if you are sharing the root of the drive.

Method 7

Remove all Macintosh volumes from MacFile. Remove SFM by using theNetwork tool in Control Panel. Do not restart the computer. Delete theIcon file and the Network trash folder from the root of the Macintoshvolume. Restart the computer. Reinstall SFM and apply the necessaryservice packs.
More information
SFM creates an in-memory index for each Macintosh volume to optimize folder and file access for Macintosh clients. Along with the appropriate disk structures, the index is updated for certain events, such as creation or deletion of folders and files, and for all permission changes. The index, which is stored on disk in the volume header, is read when SFM is started and written right after startup and again when SFM is shutdown. Attribute changes, such as folder permissions made by processes outside of SFM, to Macintosh volumes may not be correctly reflected until SFM is stopped and restarted.

For additional information about an update to SFM and index creation, click the article number below to view the article in the Microsoft Knowledge Base:
185722 SFM Rebuilds Indexes upon Restarting of Windows NT
mac tshoot resource fork corrupt corrupted

Article ID: 147909 - Last Review: 10/26/2013 07:30:00 - Revision: 2.0

  • Microsoft Windows 2000 Server
  • Microsoft Windows NT Server 3.51
  • Microsoft Windows NT Server 4.0 Standard Edition
  • kbnosurvey kbarchive kbinterop kbprb KB147909