Article ID: 159168 - View products that this article applies to.
This article was previously published under Q159168
When multiple default gateways are used in TCP/IP configuration options on a Windows NT computer, connectivity to computers on remote networks may be lost. On multihomed computers connected to disjointed networks, static routes may be added to the routing table to get connectivity to remote networks.
Windows NT computers can be configured with multiple default gateways. When a dead gateway is detected by TCP, it can direct IP to switch default gateways to the next gateway in the backup list. This switch can occur when there are multiple gateways configured for the same network adapter or when different default gateway addresses are given on various network cards on a multihomed computer. A switch is triggered when TCP has tried one-half of the TcpMaxDataRetransmissions times to send a packet through the current default gateway.
For more information on dead gateway detection and registry parameter TcpMaxDataRetransmissions, please see the following Microsoft Knowledge Base articles:
ARTICLE-ID: 128978After the switch, all IP traffic originating from any network adapter on this computer destined for remote networks will be sent to the currently selected gateway. On disjointed networks, this can lead to lost connectivity and subsequent termination of active sessions with computers on remote networks connected through the first gateway. This is because the currently selected gateway may be unaware of other routes managed by the first gateway if those routers do not exchange routing information to each other.
TITLE : Dead Gateway Detection in TCP/IP for Windows NT
TITLE : How to Optimize Windows NT to Run Over Slow WAN Links w/TCP/IP
If the switched gateway is unreachable or inactive on the network, it loses connectivity to all remote sites. At this point, a ping to this computer from a remote network will fail to get a positive response. Similarly, any outgoing ping to a remote host from this computer will give a Request timed out error. This behavior is by design and conforms to TCP/IP specifications.
The following illustrations describe situations where multiple gateways are used.
Consider a computer with two network cards, Netcard1 and Netcard2, and the following IP addresses and default gateways:
Netcard1: IP Address: 18.104.22.168 Mask: 255.255.0.0 Default Gateway: 22.214.171.124 126.96.36.199 Netcard2: IP Address: 188.8.131.52 Mask: 255.255.0.0 Default Gateway: 184.108.40.206
If you want to Telnet to a workstation with an IP address of 220.127.116.11, the IP datagrams will be routed through the 18.104.22.168 gateway. If 22.214.171.124 is detected as unavailable, IP switches to the second gateway 126.96.36.199. When this gateway fails, then use 188.8.131.52, and so on. This applies only to TCP traffic and switching gateways occurs based on the mechanism described earlier. Telnet, FTP, and NetBIOS Session service network traffic use TCP for network communications.
Also consider where the two networks connected to Netcard1 and Netcard2 are disjointed (that is, not connected to each other through any other router). If there is a network (say 22.101.x.x) that is accessible only through Netcard2, the IP datagrams for this network will still be routed through 184.108.40.206 because it is the primary default gateway. To route IP datagrams destined to network 22.101.x.x through 220.127.116.11, a static route needs to be added to the routing table through the ROUTE utility. To add the route, type the following command:
route add 18.104.22.168 MASK 255.255.0.0 22.214.171.124
Another possible solution for the above scenario is to run multiprotocol routing on the multihomed Windows NT computer so it can exchange routing information with other routers on the network running Routing Information Protocol. Multiprotocol routing is available in Windows NT 3.51 Service Pack 2 or later.
For further information, please reference the following Microsoft Knowledge Base article:
ARTICLE ID: 171564
TITLE : TCP/IP Dead Gateway Detection Algorithm Updated for Windows NT
Article ID: 159168 - Last Review: February 21, 2009 - Revision: 3.0