Article ID: 263276
Any of the following can be reasons for performing a manual removal of Internet Connection Sharing (ICS) and/or network components:
- Basic TCP/IP peer-to-peer networking has already been verified to function.
- ICS does not install properly.
- Network Properties does not show the TCP/IP (Home) or TCP/IP (Shared) components after ICS installation.
- The TCP/IP (Home) or TCP/IP (Shared) components are bound to an adapter no longer installed in the system.
- ICS troubleshooting has already been attempted, and you want to rule out corrupted files and registry entries.
- The Windows IP Configuration (WINIPCFG) utility lists adapters no longer present in the system.
- WINIPCFG does not list the ICSHARE adapter after ICS has been installed.
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
How to back up and restore the registry in Windows
Old networking drivers that have since been removed may still be present in the registry, and ICS may attempt to use those for the Internet connection. If there are damaged registry entries for either ICS or networking components and adapters in Network properties, follow these steps:
- Remove ICS; to do so, follow these steps:
- Click Start, point to Settings, and then click Control Panel.
- Double-click Add/Remove Programs, and then click the Windows Setup tab.
- Click Internet Tools, and then click Details.
- Click to clear the ICS check box, and then click OK.
- Restart the computer.
- Click Start, point to Settings, click Control Panel, and then double-click the Network icon.
- Record all of the settings present here, and ensure that you have driver disks for any networking cards installed on your computer.
- Delete everything from Network properties.
- Close Network properties and click No when prompted to restart.
- Click Start, click Run, type SFC, and then click OK.
The System File Checker should start.
- Select Extract One File From Installation Disk and type in the following file:
- Click Start, in System File Checker. In the Restore from field, enter the location to the Win98 directory on the Windows 98 Second Edition CD-ROM. For example, If your CD-ROM drive is drive D, you would enter in D:\WIN98
- In the Save File In field, if not already populated, type C:\Windows\System, and then click OK.
- Repeat steps 7-9 for the following files:
- Repeat steps 7-8 for the following files, changing the Save File In location to C:\Windows\INF.
Ics.infFor additional information about how to Extract Windows Files, click the article number below
to view the article in the Microsoft Knowledge Base:
How to Extract Original Compressed Windows Files
- Save the following files to the C:\Windows\INF directory.
- Close the System File Checker.
- Click Start, click Run, type regedit, and then click OK.
- Navigate to the following registry entry:
- Remove any present subkeys that are included underneath the Net entry (these are in groups of four numbers: 0000, 0001, 0002, and so on).
- Remove the following entry, if present:
- Close Registry Editor and restart the computer.
- Reinstall the drivers for the network card or cards, ensuring that you have the latest drivers available.
- Return to Network properties in Control Panel (click Start, point to Settings, click Control Panel, and then double-click the Network icon). Verify that the following items are present:
NOTE: If you are not using a dial-up modem for ICS, you should see the names of two networking cards on your computer. If you are using a dial-up modem for ICS, one of these adapters should be a dial-up adapter. If you need a TCP/IP or dial-up adapter and do not see one, follow these steps for adding components:
- Client for Microsoft Networks
- (Adapter Card #1)
- (Adapter Card #2)
- TCP/IP --> (Adapter Card #1)
- TCP/IP --> (Adapter Card #2)
If there are any extra components listed at this time, remove any unused protocols such as IPX/SPX Compatible Protocol or Client for Netware Networks.
- Click Add, select Protocol for TCP/IP (or) Adapter, and then click Add.
- Select Microsoft for the manufacturer, click the item that you are adding, and then click OK.
- Close Network properties and restart the computer.
- Reinstall ICS through the Add/Remove Programs feature in Control Panel.
Article ID: 263276 - Last Review: June 19, 2014 - Revision: 2.0
|kbenv kbhowto kbinfo kbnetwork KB263276|Retired KB Content Disclaimer
This article was written about products for which Microsoft no longer offers support. Therefore, this article is offered "as is" and will no longer be updated.