How to create a merge document using a text data source in Word for Mac
This article was previously published under Q275014
This article has been archived. It is offered "as is" and will no longer be updated.
For a Microsoft Word 98 version of this article, see 178716.
This article provides detailed instruction on creating a simple data mergeusing data stored in a text document. By following these instructions youwill create a form letter (main document), select the text data document,and merge the information in the two documents into a third document.
The following is general information about the appropriate format for atext document that will be used as a data document in a simple MicrosoftWord for Mac data merge.
The data should be separated by a special character called a delimiter. Themost common delimiters are tabs or commas. When a comma is used as adelimiter, the text in each field is usually enclosed in quotation marks sothat a punctuation mark inside a field will not be interpreted as adelimiter.
What Is a Record?A record consists of a series of fields separated by delimiters. Eachrecord ends with a paragraph mark. Records may appear to extend overmultiple lines but each record ends at the first paragraph mark. In a textdata source, each record must have exactly the same number of delimiters init, as in the following example:
FName<Tab>LName<Tab>Address1<Tab>Address2<RETURN> Betty<Tab>Smith<Tab>1401 A St.<Tab>Apt. 5<RETURN> George<Tab>Jones<Tab>345 Pile Ln.<Tab><Tab><RETURN>In this example, the first record has four fields separated by three <tabs>(delimiters).The word <RETURN> represents the character you get when you press theRETURN key. This denotes the end of the record. The first record, known as the header record contains the field names that will be used for the merge. The second and subsequent records contain the actual data. Notice that thelast field in the third record has no information in it, but the delimiter(tab) is still required to hold its place. Theremust be the same number of delimiters in every record. Any field can beleft empty in any record except the first record, which must contain afield name for each field. The delimiters on each side of an empty fieldmust be in place.
Field names should contain no punctuation and usually consist of one word.Spaces can be used in field names but it is better to use one-word fieldnames until you are more familiar with the process.
TIP: Combining information in separate fields in a merge document is easy;however, separating information in a field is difficult. So, when youcreate a data document, create as many fields as is practical. For example,you may want to put the first name in a field separate from the last nameto make it easy to sort the records in the data document by last name.Keeping the first and last name separate will also make it easy to use onlythe first name in a salutation.
Once you have created and saved your data document, use the followinginstructions to create a form letter and perform a mail merge using thedata stored in the text document.
CREATING THE MAIN DOCUMENTTo create the main document, follow these steps:
- Start Word for Mac.
- In the Project Gallery, click Word Document.
The insertion point should be blinking in Document1. This indicates that Document1 is the active document.
- On the Tools menu, click Data Merge Manager.
The Data Merge Manager appears on the screen.
- In the Data Merge Manager, click Create and then click Form Letters.
Selecting the Data Source
- In the Data Merge Manager, click Get Data, and then click Open Data Source.
- Select the data document and click Open.
- If the Header Record Delimiters dialog box appears, select the correct field delimiter and record delimiter and click OK.
EDITING THE MAIN DOCUMENTThe insertion point should be back in Document1 (that is, Document1 shouldbe the active document) and the Data Merge Manager should be visible.
To edit the main document (Document1 in this case), follow these steps:
- Type some text in the document.
- Click where you want to insert the first field. In the Data Merge Manager, under Merge field, drag the field name that you want to use into the main document.
Repeat steps 1 and 2 as many times as necessary to create the appropriate text and insert the merge fields you want in the main document.
NOTE: When you merge data, you can use as few or as many of the data fields as you need to and you can use them in any order. Also, each field can be used more than one time.
- To save the main document, click Save or Save As on the File menu.
TIP: Use a name that identifies this document as a main document (for example, name the file "My Main Document"). The document should be stored in the same location (folder) as the data document.
MERGING THE MAIN DOCUMENT AND THE DATA DOCUMENTTo perform the merge, click the Merge To New Document button in the Data Merge Manager. This creates a new document containing the results of themerge. This new document can be printed, saved, or deleted withoutaffecting either the main document or the data document.
TIP: Once you have a simple merge working correctly, you can change details one at a time to increase the complexity of the merge. Be sure to test the merge after you make a change.
For more information about data merge and data document types, click the Office Assistant, type data merge, click Search, and then click a topic to view it.
NOTE: If the Assistant is hidden, click the Office Assistant button on the Standard toolbar.
form letter mailmerge standard bulk mailing multiple mac macword WD2001KB mail merge print datamerge WD2001 word DMM basic simple data combine field document main label catalog
Article ID: 275014 - Last Review: 12/05/2015 21:58:59 - Revision: 3.0
Microsoft Word 2004 for Mac, Microsoft Word X for Mac, Microsoft Word 2001 for Mac
- kbnosurvey kbarchive dftsdahomeportal kbinfo kbmerge KB275014