You cannot install Windows XP successfully after you use Windows Vista or Windows PE 2.0 to create partitions on a hard disk

Support for Windows XP has ended

Microsoft ended support for Windows XP on April 8, 2014. This change has affected your software updates and security options. Learn what this means for you and how to stay protected.

This article has been archived. It is offered "as is" and will no longer be updated.
You use Windows Vista or Windows Preinstallation Environment (Windows PE) 2.0 to create partitions on a hard disk. After you do this, you try to install Microsoft Windows XP on the hard disk without using Windows XP to repartition the disk. In this case, you cannot install Windows XP successfully.

Windows XP Setup successfully completes the text-mode part of Setup. However, after the text-mode part of Setup is complete, the computer cannot be restarted successfully to enter the graphical user interface (GUI)-mode part of Setup. Additionally, the computer may stop responding. You may receive an error message that resembles one of the following:
A disk read error occurred
Unable to load operating system
Error loading operating system
When you deploy a Windows XP Professional sysprep image to a system, the system may continuously restart after you start the system for the first time. If you press F8 and then disable the "automatic restart" option, you may receive the following Stop error:
Stop: 0x000000ED (0X81F85678, 0xC000014F,0x00000000,0x00000000)
Additionally, if you view the disk in Windows PE 2.0, the disk may appear as "raw."
This problem occurs because Windows Vista and Windows PE 2.0 create disk partitions differently than Windows XP. This problem occurs only on computers that use certain BIOS firmware.
To work around this problem, use one of the following methods.

Method 1: Disable the "automatic disk translation" feature

Before you partition the hard disk, you can disable the "automatic disk translation" feature in the BIOS configuration. For example, you can change the disk type from Auto to Large.

Method 2: Modify the registry to use the Windows XP disk partition procedure

Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 How to back up and restore the registry in Windows

Before you partition the hard disk in Windows Vista or in Windows PE 2.0, modify the registry so that the partitions are created by using the Windows XP procedure. To do this, follow these steps:
  1. Click Start, click Run, type regedit, and then click OK.
  2. Locate and then click the following registry subkey:
  3. On the Edit menu, point to New, and then click DWORD value.
  4. Type LessThan4GB as the new entry name.
  5. Right-click LessThan4GB, and then click Modify.
  6. In the Edit DWORD Value dialog box, click Decimal.
  7. In the Value data box, type 0, and then click OK.
  8. Repeat steps 3 through 7 to add the following registry entries:
    • Between4_8GB
    • Between8_32GB
    • GreaterThan32GB
    Each registry entry must have a value of 0.
  9. Exit Registry Editor.

Method 3

If you are using Microsoft Deployment Toolkit 2008 to deploy Windows XP, follow these steps:
  1. In the properties of the task sequence, click the Task Sequence tab.
  2. Click Preinstall, and then click New Computer Only.
  3. Click Set Diskpart BIOS Compatibility Mode.
  4. On the Options tab, click to clear the Disable this step check box.
When you use the Windows Vista or Windows PE 2.0 partition procedure to create a partition, the partition border is constructed based on the registry setting on the system. However, when you use the Windows XP partition procedure to create a partition, the partition border is aligned according to the cylinder boundary.

When you create a partition, free space that is followed by the first partition is created at the beginning of the disk. The size of the free space is determined based on how the partition border is constructed. Therefore, the size may vary, depending on how the partition is created.

When you create a partition by using the Windows XP procedure, this free space is equal to one cylinder. However, when you create a partition by using the Windows Vista or Windows PE 2.0 procedure, the free space varies, depending on the registry setting.
To resolve this problem, you must integrate the hotfix into the source files of the Windows XP installation before you install Windows XP. For more information about how to integrate this hotfix into the Windows installation source files, click the following article number to view the article in the Microsoft Knowledge Base:
828930How to integrate software updates into your Windows installation source files

Hotfix information

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that is described in this article. Apply this hotfix only to systems that are experiencing this specific problem. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.

If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix.

Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft Web site: Note The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.


This hotfix requires Windows XP Service Pack 2 (SP2).

322389 How to obtain the latest Windows XP service pack

Restart requirement

You have to restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace any other hotfixes.

File information

The English version of this hotfix has the file attributes (or later file attributes) that are listed in the following table. The dates and times for these files are listed in Coordinated Universal Time (UTC). When you view the file information, it is converted to local time. To find the difference between UTC and local time, use the Time Zone tab in the Date and Time item in Control Panel.
Windows XP with SP2, x86-based versions
File nameFile versionFile sizeDateTimePlatform
Ntoskrnl.exe5.1.2600.30862,182,14419-Feb-2007 10:44x86
Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the"Applies to" section.
CM70332, AMI BIOS. windows XP, 931760 winpe

Article ID: 931760 - Last Review: 12/09/2015 09:28:49 - Revision: 6.0

Microsoft Windows XP Professional, Microsoft Windows XP Home Edition, Microsoft Windows XP Media Center Edition, Microsoft Windows XP Starter Edition

  • kbnosurvey kbarchive kbautohotfix kbfix kbexpertiseinter kbhotfixserver kbqfe KB931760