This error is reported to USB device drivers by the Microsoft USB core driver stack via the USB status code USBD_STATUS_XACT_ERROR if the USB EHCI host controller sets the Transaction Error (XactErr) bit in the USB transfer descriptor upon completion of the USB transfer. The USB EHCI host controller sets this bit if it detects that certain bus protocol errors occur during communication with the USB device.
Thus, the cause of a USB Transaction Error (XactErr) is one of the following:
- An error in the communications with a USB device over the USB bus, caused by either the device, an external USB hub connected between the device and the USB host controller/root hub, or a faulty USB cable.
- An error in the USB EHCI host controller itself, resulting in an erroneous report of a USB Transaction Error when in fact no error in USB bus communications occurred.
To identify the cause of a USB Transaction Error, a careful examination of the USB bus traffic during the time that the error was reported must be performed.
- If examination of USB traces reveals a communication error committed by the USB device or hub that would be expected to result in a USB Transaction Error, the vendor of the faulting device should be engaged to diagnose and resolve the problem with the connected USB hardware.
- Whether examination of USB traces reveals communication errors that would be expected to result in a USB Transaction Error or not, it's possible that at least one of the USB cables connected is faulty. All cables involved in the connection should be replaced with known certified USB cables. If a faulty USB cable is located between the USB bus analyzer and the attached device, then communication errors may be seen by the USB analyzer. If a faulty USB cable is located between the USB host controller/root hub port and the USB bus analyzer, communication errors may not be seen by the USB analyzer, but may still be seen by the USB host controller.
- If examination of USB traces reveals no communication errors that would be expected to result in a USB Transaction Error, and if the problem is not resolved by replacing the USB cables with known certified USB cables, then it's likely that the USB EHCI host controller erroneously reported a USB Transaction Error. In this case, the vendor of the USB EHCI host controller should be contacted for further information. Since USB EHCI host controllers are often embedded in the main chipset of the computer's motherboard, a resolution for a USB EHCI host controller error (erratum) may not be available.
To recover from USB transfers which fail with a USB status of USBD_STATUS_XACT_ERROR, USB device driver developers should take the following actions:
- Issue a URB_FUNCTION_RESET_PIPE request for the USB endpoint that is the target of the failed transfer. This action is normally expected to clear errors such as a Transaction Error (XactErr), and allow subsequent USB transfers to resume.
- Before issuing a URB_FUNCTION_RESET_PIPE request, a URB_FUNCTION_ABORT_PIPE request should be issued for the USB endpoint that is the target of the failed transfer. The URB_FUNCTION_ABORT_PIPE request will cancel all pending transfers for the specified endpoint, which is documented in the Windows Driver Kit (WDK) as a prerequisite to issuing a URB_FUNCTION_RESET_PIPE request.
- If the above actions fail to allow subsequent USB transfers to resume for the specified USB device and endpoint, an IOCTL_INTERNAL_USB_RESET_PORT request may be issued by a kernel-mode USB device driver to reset the USB port to which the USB device is attached. All pending transfers to all endpoints of the USB device should be cancelled via URB_FUNCTION_ABORT_PIPE requests, and the USB device driver should wait for these transfers to complete, before isssuing this request.
- Finally, if all of the above actions fail to restore communications with the USB device following a Transaction Error, a kernel-mode USB device driver may issue an IOCTL_INTERNAL_USB_CYCLE_PORT to cause the USB device to be effectively removed from and re-enumerated on the USB port to which it is attached. All pending transfers to all endpoints of the USB device should be cancelled via URB_FUNCTION_ABORT_PIPE requests, and the USB device driver should wait for these transfers to complete, before isssuing this request.
Installing the hotfixes referenced in Microsoft Knowledge Base article 908673 or 913365, and setting the EnSoftRetry registry value as documented in Microsoft Knowledge Base article 908673, may suppress reporting of a USBD_STATUS_XACT_ERROR for a USB transfer which completes with a USB Transaction Error (XactErr) and cause the transfer to be automatically retried. However, since the original transfer actually failed, this behavior may be undesirable. A USB device driver may need to be aware of the fact that the transfer actually failed, so that appropriate action can be taken. In such situations, the hotfixes referenced in Microsoft Knowledge Base article 908673 or 913365 should not be installed, and the EnSoftRetry registry value should not be set, to allow USB Transaction Errors to be reported to the USB device driver for appropriate action.
In the "Enhanced Host Controller Interface Specification for Universal Serial Bus" (henceforth referred to as the USB EHCI Spec), a Transaction Error is described in sections 3.3.2, 3.4.3, and 3.5.3 as follows:
|Bit||Status Field Description|
Transaction Error (XactErr).
Set to a one by the Host Controller during status update in the case where the host did not receive a valid response from the device (Timeout, CRC, Bad PID, etc.). Refer to Section 126.96.36.199 for summary of the conditions that affect this bit. If the host controller sets this bit to a one, then it remains a one for the duration of the transfer.
Section 188.8.131.52 of the USB EHCI Spec states:
184.108.40.206 Transaction Error
A transaction error is any error that caused the host controller to think that the transfer did not complete successfully. Table 4–18 lists the events/responses that the host can observe as a result of a transaction. The effects of the error counter and interrupt status are summarized in the following paragraphs. Most of these errors set the XactErr status bit in the appropriate interface data structure.
Additional details can be found in sections 220.127.116.11, 18.104.22.168.1, and 22.214.171.124.2 of the USB EHCI Spec.
The Enhanced Host Controller Interface Specification for Universal Serial Bus is downloadable from:
You may search for certified USB Implementers Forum, Inc. (USB-IF) logo compliant products at:
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, MICROSOFT AND/OR ITS SUPPLIERS DISCLAIM AND EXCLUDE ALL REPRESENTATIONS, WARRANTIES, AND CONDITIONS WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO REPRESENTATIONS, WARRANTIES, OR CONDITIONS OF TITLE, NON INFRINGEMENT, SATISFACTORY CONDITION OR QUALITY, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE MATERIALS.
Artikel-id: 960958 - Laatst bijgewerkt: 8 dec. 2008 - Revisie: 1