x86 Protected Mode Exceptions

Zavrnitev odgovornosti za umaknjeno vsebino KB

Ta članek govori o izdelkih, za katere Microsoft ne ponuja več podpore. Zato je ta članek na voljo »tak, kot je«, in ne bo več posodobljen.


The following chart lists the exceptions that can be generated by the Intel 80286, 80386, 80486, and Pentium processors:

Exception | Description
(dec/hex) |
0 00h | Divide error:
| Occurs during a DIV or an IDIV instruction when the
| divisor is zero or a quotient overflow occurs.

1 01h | Single-step/debug exception:
| Occurs for any of a number of conditions:
| - Instruction address breakpoint fault
| - Data address breakpoint trap
| - General detect fault
| - Single-step trap
| - Task-switch breakpoint trap

2 02h | Nonmaskable interrupt:
| Occurs because of a nonmaskable hardware interrupt.

3 03h | Breakpoint:
| Occurs when the processor encounters an INT 3 instruction.

4 04h | Overflow:
| Occurs when the processor encounters an INTO instruction
| and the OF (overflow) flag is set.

5 05h | Bounds check (BOUND instruction):
| Occurs when the processor, while executing a BOUND
| instruction, finds that the operand exceeds the specified
| limit.

6 06h | Invalid opcode:
| Occurs when an invalid opcode is detected.

7 07h | Coprocessor not available:
| Occurs for one of two conditions:
| - The processor encounters an ESC (escape) instruction
| and the EM (emulate) bit of CR0 (control register zero)
| is set.
| - The processor encounters either the WAIT instruction or
| an ESC instruction and both the MP (monitor
| coprocessor) and TS (task switched) bits of CR0 are set.

8 08h | Double fault:
| Occurs when the processor detects an exception while
| trying to invoke the handler for a prior exception.

9 09h | Coprocessor segment overrun:
| Occurs when a page or segment violation is detected while
| transferring the middle portion of a coprocessor operand
| to the NPX.

10 0Ah | Invalid TSS:
| Occurs if, during a task switch, the new TSS is invalid.

11 0Bh | Segment not present:
| Occurs when the processor detects that the present bit of
| a descriptor is zero.

12 0Ch | Stack exception:
| Occurs for one of two conditions:
| - As a result of a limit violation in any operation that
| refers to SS (stack segment register)
| - When attempting to load SS with a descriptor that is
| marked as not-present but is otherwise valid

13 0Dh | General protection violation:
| Each protection violation that does not cause another
| exception causes a general protection exception.
| - Exceeding segment limit when using CS, DS, ES, FS, or GS
| - Exceeding segment limit when referencing a descriptor
| table
| - Transferring control to a segment that is not executable
| - Writing to a read-only data segment or a code segment
| - Reading from an execute-only segment
| - Loading SS with a read-only descriptor
| - Loading SS, DS, ES, FS, or GS with a descriptor of a system
| segment
| - Loading DS, ES, FS, or GS with the descriptor of an
| executable segment that is also not readable
| - Loading SS with the descriptor of an executable segment
| - Accessing memory through DS, ES, FS, or GS when the segment
| register contains a NULL selector
| - Switching to a busy task
| - Violating privilege rules
| - Loading CR0 with PG=1 and PE=0
| - Interrupt or exception through trap or interrupt gate from
| V86 mode to a privilege level other than 0

14 0Eh | Page fault:
| Occurs when paging is enabled (PG=1) and the processor
| detects one of the following conditions while translating
| a linear address to a physical address:
| - The page-directory or page-table entry needed for the
| address translation has 0 in its present bit.
| - The current procedure does not have sufficient privilege
| to access the indicated page.

15 0Fh | (Reserved)

16 10h | Coprocessor error:
| Occurs when the processor detects a signal from the
| coprocessor on the ERROR# input pin.

17 11h | (Reserved)
through |
31 1Fh |


"Intel 80386 Programmer's Reference Manual,"

ID članka: 117389 – Zadnji pregled: 14. okt. 2003 – Revizija: 1

Povratne informacije