How to Map a Port in ICS Using an .inf File

BB İçeriği Yasal Uyarısı Kaldırıldı

Bu makale, Microsoft'un artık destek sağlamadığı ürünler ile ilgili olarak yazılmıştır. Bu nedenle, bu makale "olduğu gibi" sunulmaktadır ve bundan sonra güncelleştirilmeyecektir.


This article describes how to create a new port mapping for Internet Connection Sharing (ICS) by using an .inf file. The .inf file adds additional port mappings to direct incoming IP packets through a specific UDP or TCP port or to a specific client address. Certain Internet programs may require a specific port to be reserved for their use. This information should be provided by the manufacturer of the program.

If port addressing information is stored within the data section of a TCP or UDP packet used by a particular program, an editor is required and this .inf file will not facilitate the program's functionality with an ICS host. In these cases, the ICS host should be disabled and the program should run on a computer directly connected to the Internet.

Although Microsoft provides this informational article for the convenience of its customers, Microsoft Product Support Services does not provide support for the use or editing of the .inf file in this article.

NOTE: This article is for informational use only. It does not contain any troubleshooting information. If you are searching for troubleshooting information that is not mentioned in this article, search the Microsoft Knowledge Base again by using keywords that are listed in the following Microsoft Knowledge Base article:
242450 How to Query the Microsoft Knowledge Base Using Keywords

More Information

You can create the base contents of the .inf file by copying or typing the information below into a new file. After the .inf file is created, you can right-click the file and then click Install.

NOTE: Each entry that starts with a semicolon (;) is a comment. These lines can be removed. They are provided to describe each line. The computer must be rebooted for the registry values added by this .inf file to take effect. This .inf file should be used only on the computer running ICS.

Sample .inf File

NOTE: Setup information (.inf) files use "HKLM" as an abbreviation for the "HKEY_LOCAL_MACHINE" registry hive.



; This section included for ease of removing any maps added in.
; To uninstall, type the following line:
; rundll.exe setupx.dll,InstallHinfSection DefaultUnInstall 0

; MYMAPNAME should be replaced with a friendly
; descriptive name that is unique.
; This data points to the computer that is running the service.
; represents the computer running the ICS services. This
; can alternatively contain the IP address of one of the ICS client
; computers.


; "My Friendly Name" should be replaced with something short and
; descriptive such as the name of the program that needs these ports
; open.


; Options is a DWORD value and is currently always set to 00,00,00,00


; The next four lines describe the specific ports that need to be open
; or mapped. The first port is always 0000, each additional port is
; incremented (the second port to open would be listed as 0001,
; the third would be 0002, and so on). This information is strictly
; dependent on what is needed by the program. If you do not know what
; ports your program requires or are unsure, you need to contact the
; manufacturer of the program to get this information.
; The four lines need to be re-created for each port.
; On the second line, valid entries for type are "TCP" or "UDP."
; The third line contains the actual port or port range needed by the
; program.
; The entry below demonstrates a port range. If the program only needs
; a single port, the last part of the line below would read ,Port,,"5678"
; Note that you can only use a port range when the translation type is
; If Translation is set to anything else, you must list each port
; individually.
; Valid types of translation are NORMAL, BLOCK, CUSEEME, DPLAY, FTP,
; H323, PPTP, and QUAKE




Makale No: 231162 - Son İnceleme: 22 Haz 2014 - Düzeltme: 1

Geri bildirim