Set up a TV signal in Windows Media Center

If your TV signal comes from a cable TV jack in the wall or an over-the-air antenna, follow these steps to set it up in Media Center:

1. Connect your TV signal cable to the TV-IN jack on a compatible TV tuner on your Media Center PC.
   
   If your PC has more than one tuner, you can use a cable splitter to divide the TV signal, and then connect it to each tuner. This will enable you to record multiple programs simultaneously, or to watch a live program while recording another program. To receive a TV signal using multiple tuners, each tuner must have a TV signal connected to it, and the signal must be the same for each tuner.

2. On the Windows Media Center start screen, scroll to Tasks, select Settings, select TV, and then select Set Up TV Signal.

3. If you see a message saying that changing the settings will affect TV recording, it means you already have a signal set up. To go through the set up process again, select Yes.

4. Follow the steps to set up your TV signal. These steps will vary depending on the type of tuner or tuners that you have, as well as the type of programming to which you subscribe.

5. On the TV Signal Detection Result screen, if you see your tuner or tuners listed as expected, select Yes, configure TV with these results, and then select Next.
   
   If a TV tuner is not showing up on this screen, make sure that it's connected properly to your computer, and that you have the appropriate drivers installed. For more information, see Update a driver for hardware that isn't working properly.

6. On the TV Signal Provider screen, scroll through the list and select the signal provider that most closely matches your location and service, and then select Next.

7. Select Finish.

If you set up a digital TV tuner during the setup process, you can scan for additional channels that might be available. You can also check the signal strength for each channel, and turn off channels that aren't receiving a strong signal.

• On the Windows Media Center start screen, scroll to Tasks, select Settings, select TV, select TV Signal, and then do one of the following:

  • Select Scan for More Channels, and then follow the instructions. Media Center will look for additional channels that might be available for your TV tuner.

  • Select Digital TV Antenna Signal Strength, and then follow the instructions. Media Center will scan each channel individually and display its signal strength. On the Adjust Digital TV Antenna and Choose Channels screen, you can clear the check box next to channels with little or no signal so they won't show up in the Guide.

Many cable or satellite subscribers have a cable box (sometimes referred to as a set-top box) or satellite receiver. You can set up your TV signal to pass through one of these devices on its way to your Media Center PC.

Cable boxes and satellite receivers can include channels that are either standard or high definition. In Media Center, a digital high-definition signal that is transmitted through one of these boxes will be converted to an analog standard-definition signal.

1. Connect the cable from the cable source (wall jack) to the cable input jack on the cable box or satellite receiver.
   
   If you have two cable boxes or two satellite receivers that you want to use with Media Center, you can use a splitter to divide the TV signal from the wall jack to the boxes. Each cable box or satellite receiver must have a TV signal connected to the cable input jack.

2. Connect a cable from the output jack on the cable box or satellite receiver to the TV-IN jack on the appropriate TV tuner on your Media Center PC.
   
   If your PC has more than one TV tuner, make sure each tuner has its own TV signal connected to the TV-IN jack. (This means that you'll need one cable box or satellite receiver for each TV tuner on your Media Center PC.)

3. Connect an IR blaster to your computer and your set-top box. (An IR blaster is a small, infrared device that is packaged with many Media Center remote controls and TV tuners. For more information, see the documentation that came with your IR blaster.)

4. On the Windows Media Center start screen, scroll to Tasks, select Settings, select TV, and then select Set Up TV Signal.

5. Follow the steps to connect a TV signal, depending on the type of tuner or tuners that the cable is connected to, as well as the type of programming to which you subscribe.

If you have a digital cable service from your local cable provider, and you own a specially certified PC known as a Digital Cable Ready computer, you may be able to watch and record digital cable TV in Media Center. To do this you'll need a couple things: a digital cable tuner, which is a device that comes with most Digital Cable Ready computers, and a CableCARD, which is a device that must be inserted into your digital cable tuner to allow it to receive digital cable. A CableCARD serves as a replacement for a digital set-top box, and can only be obtained from a participating digital cable provider. With the proper CableCARD inserted into a compatible digital cable tuner, you can watch digital cable channels (both standard and high definition) that are available by subscription from your cable provider.


It's recommended that you work with a cable technician from your service provider to set up a digital cable tuner and signal. Many of the steps below should be performed by them.

1. If you have a Digital Cable Ready computer, follow the instructions from your computer manufacturer to set up your digital cable tuner.

2. Write down the UnitAddress and the CableCARD S/N (serial number) from the outside of your CableCARD. (You'll need these numbers for the activation process in step 7.)

3. Insert the CableCARD into the digital cable tuner. (This step is usually performed by a technician from your digital cable provider.)

4. Connect the cable from the cable source (wall jack) to the TV-IN jack on the digital cable tuner. (This step is usually performed by a technician from your digital cable provider.)

5. On the Windows Media Center start screen, scroll to Tasks, select Settings, select TV, select Set Up TV Signal, and then follow the steps to set up the signal.

6. Contact your service provider to pair your CableCARD with the digital cable tuner—this will activate both so you can receive digital cable content. You will be required to provide the following information to your service provider:

   • CableCARD ID. This number will be reported in Windows Media Center on the Call your cable company page. (Example: 000-298-933-268-5)

   • Host ID. This number will be reported in Windows Media Center on the Call your cable company page. (Example: 029-000-000-104-7)

   • Data ID. This number will be reported in Windows Media Center on the Call your cable company page. (Example: 132-028-947-08)

   • UnitAddress. You'll find this number on the outside of your CableCARD device. (Example: 000-02989-33268-246)

   • CableCARD S/N. You'll find this number on the outside of your CableCARD device. (Example: NG3549TA0113)

If you upgraded your computer to Windows 7 from Windows Vista, you might be able to preserve your TV signal settings from before the upgrade.

1. Select the Start button  , select All Programs, and then select Windows Media Center.

2. If Media Center detects previous TV signal settings, you'll see a welcome message asking if you want to set up the TV with the same settings. Select Yes, use my previous TV settings, and then select OK.

3. When Media Center is finished applying previous TV settings, select Finish.

If you're having trouble setting up your TV signal, try using the Set up TV tuner troubleshooter to automatically find and fix some common problems.

Open the Set up TV tuner troubleshooter by selecting the Start button  , and then selecting Control Panel. In the search box, enter troubleshooter, and then select Troubleshooting. In the left pane, select View all, and then select Set up TV tuner.