Applies ToWindows Server 2008 Service Pack 2 Windows Server 2008 Enterprise Windows Server 2008 Enterprise without Hyper-V Windows Server 2008 Datacenter Windows Server 2008 Datacenter without Hyper-V Windows Server 2008 for Itanium-Based Systems Windows Server 2008 Foundation Windows Server 2008 Standard Windows Server 2008 Standard without Hyper-V Windows Server 2008 Web Edition

Symptoms

Assume that you remove all the paths to a storage area network (SAN) storage device from a computer that is running Windows Server 2008 Service Pack 2 (SP2). The storage arrays support asymmetric logical unit access (ALUA). When you try to perform one of the following operations, the computer crashes:

  • Open the Microsoft Multipath I/O (MPIO) console.

  • Switch to the MPIO tab in the Properties dialog box of a disk that is managed by MPIO.

  • Run the Mpclaim.exe command together with the -b, -v, or -d option from the command prompt.

Additionally, you receive a Stop error message that resembles the following:

STOP: 0x000000D1 (parameter1, parameter2, parameter3, parameter4)

Notes

  • This Stop error describes a DRIVER_IRQL_NOT_LESS_OR_EQUAL issue.

  • The parameters in this Stop error message vary, depending on the configuration of the computer.

  • Not all "Stop 0x000000D1" errors are caused by this issue.

Cause

This issue occurs because the system does not perform a null check before dereferencing the target port of the device.

Resolution

Hotfix information

A supported hotfix is available from Microsoft. However, this hotfix is intended to correct only the problem that is described in this article. Apply this hotfix only to systems that are experiencing the problem described in this article. This hotfix might receive additional testing. Therefore, if you are not severely affected by this problem, we recommend that you wait for the next software update that contains this hotfix.If the hotfix is available for download, there is a "Hotfix download available" section at the top of this Knowledge Base article. If this section does not appear, contact Microsoft Customer Service and Support to obtain the hotfix. Note If additional issues occur or if any troubleshooting is required, you might have to create a separate service request. The usual support costs will apply to additional support questions and issues that do not qualify for this specific hotfix. For a complete list of Microsoft Customer Service and Support telephone numbers or to create a separate service request, visit the following Microsoft website:

http://support.microsoft.com/contactus/?ws=supportNote The "Hotfix download available" form displays the languages for which the hotfix is available. If you do not see your language, it is because a hotfix is not available for that language.

Prerequisites

To apply this hotfix, you must be running Windows Server 2008 SP2.For more information about how to obtain a Windows Server 2008 service pack, click the following article number to view the article in the Microsoft Knowledge Base:

968849How to obtain the latest service pack for Windows Server 2008

Registry information

To apply this hotfix, you do not have to make any changes to the registry.

Restart requirement

You must restart the computer after you apply this hotfix.

Hotfix replacement information

This hotfix does not replace a previously released hotfix.

The global version of this hotfix installs files that have the attributes that are listed in the following tables. The dates and the times for these files are listed in Coordinated Universal Time (UTC). The dates and the times for these files on your local computer are displayed in your local time together with your current daylight saving time (DST) bias. Additionally, the dates and the times may change when you perform certain operations on the files.

Windows Server 2008 file information notesImportant Windows Vista hotfixes and Windows Server 2008 hotfixes are included in the same packages. However, only "Windows Vista" is listed on the Hotfix Request page. To request the hotfix package that applies to one or both operating systems, select the hotfix that is listed under "Windows Vista" on the page. Always refer to the "Applies To" section in articles to determine the actual operating system that each hotfix applies to.

  • The files that apply to a specific product, SR_Level (RTM, SPn), and service branch (LDR, GDR) can be identified by examining the file version numbers as shown in the following table.

    Version

    Product

    SR_Level

    Service branch

    6.0.600 2. 23xxx

    Windows Server 2008

    SP2

    LDR

  • The MANIFEST files (.manifest) and the MUM files (.mum) that are installed for each environment are listed separately in the "Additional file information for Windows Server 2008" section. MUM files and MANIFEST files, and the associated security catalog (.cat) files, are extremely important to maintaining the state of the updated component. The security catalog files, for which the attributes are not listed, are signed with a Microsoft digital signature.

For all supported x86-based versions of Windows Server 2008

File name

File version

File size

Date

Time

Platform

Msdsm.sys

6.0.6002.23185

92,096

08-Aug-2013

10:42

x86

For all supported x64-based versions of Windows Server 2008

File name

File version

File size

Date

Time

Platform

Msdsm.sys

6.0.6002.23185

111,552

08-Aug-2013

12:12

x64

For all supported IA-64-based versions of Windows Server 2008

File name

File version

File size

Date

Time

Platform

Msdsm.sys

6.0.6002.23185

276,928

08-Aug-2013

12:12

IA-64

Status

Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section.

More Information

For more information about a similar issue in Windows Server 2008 R2 or Windows Server 2012, click the following article number to view the article in the Microsoft Knowledge Base:

2821052 "0x000000D1" Stop error when you open the MPIO snap-in on a computer that is running Windows Server 2008 R2 or Windows Server 2012 For more information about software update terminology, click the following article number to view the article in the Microsoft Knowledge Base:

824684Description of the standard terminology that is used to describe Microsoft software updates

Additional file information for Windows Server 2008

Additional files for all supported x86-based versions of Windows Server 2008

File property

Value

File name

X86_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_cc65c263f20bf5bc.manifest

File version

Not applicable

File size

1,664

Date (UTC)

08-Aug-2013

Time (UTC)

13:52

Platform

Not applicable

Additional files for all supported x64-based versions of Windows Server 2008

File property

Value

File name

Amd64_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_28845de7aa6966f2.manifest

File version

Not applicable

File size

1,666

Date (UTC)

08-Aug-2013

Time (UTC)

13:52

Platform

Not applicable

Additional files for all supported IA-64-based versions of Windows Server 2008

File property

Value

File name

Ia64_msdsm.inf_31bf3856ad364e35_6.0.6002.23185_none_cc676659f209feb8.manifest

File version

Not applicable

File size

1,665

Date (UTC)

08-Aug-2013

Time (UTC)

13:52

Platform

Not applicable

Need more help?

Want more options?

Explore subscription benefits, browse training courses, learn how to secure your device, and more.

Communities help you ask and answer questions, give feedback, and hear from experts with rich knowledge.