Release Date:

8/13/2024

Version:

OS Build 22000.3147

07/09/24---END OF SERVICE NOTICE---

IMPORTANT All editions of Windows 11, version 21H2 will reach end of service on October 8, 2024. After that date, these devices will not receive monthly security and non-security updates. These updates contain protections from the latest security threats. To continue receiving these updates, we recommend that you update to the latest version of Windows.

For information about Windows update terminology, see the article about the types of Windows updates and the monthly quality update types. For an overview of Windows 11, version 21H2, see its update history page

Note Follow @WindowsUpdate to find out when new content is published to the Windows release health dashboard.       

Tip: Looking for this month's video? It's now in the article for Windows 11, versions 22H2 and 23H2.

Highlights  

  • This update addresses security issues for your Windows operating system. 

Improvements

This security update includes improvements. Below is a summary of the key issues that this update addresses when you install this KB. If there are new features, it lists them as well. The bold text within the brackets indicates the item or area of the change we are documenting.

  • [Protected Process Light (PPL) protections] You can bypass them.

  • [Windows Kernel Vulnerable Driver Blocklist file (DriverSiPolicy.p7b)] This update adds to the list of drivers that are at risk for Bring Your Own Vulnerable Driver (BYOVD) attacks.

  • [BitLocker (known issue)] A BitLocker recovery screen shows when you start up your device. This occurs after you install the July 9, 2024, update. This issue is more likely to occur if device encryption is on. Go to Settings > Privacy & Security > Device encryption. To unlock your drive, Windows might ask you to enter the recovery key from your Microsoft account.

  • [Lock screen] This update addresses CVE-2024-38143. Because of this, the “Use my Windows user account” checkbox is not available on the lock screen to connect to Wi-Fi.

  • [NetJoinLegacyAccountReuse] This update removes this registry key. For more information refer to KB5020276—Netjoin: Domain join hardening changes.

  • [Secure Boot Advanced Targeting (SBAT) and Linux Extensible Firmware Interface (EFI)] This update applies SBAT to systems that run Windows. This stops vulnerable Linux EFI (Shim bootloaders) from running. This SBAT update will not apply to systems that dual-boot Windows and Linux. After the SBAT update is applied, older Linux ISO images might not boot. If this occurs, work with your Linux vendor to get an updated ISO image.

If you installed earlier updates, only the new updates contained in this package will be downloaded and installed on your device.

For more information about security vulnerabilities, please refer to the Security Update Guide website and the August 2024 Security Updates.

Windows 11 servicing stack update (KB5041591) - 22000.3139

This update makes quality improvements to the servicing stack, which is the component that installs Windows updates. Servicing stack updates (SSU) ensure that you have a robust and reliable servicing stack so that your devices can receive and install Microsoft updates.

Known issues in this update

Applies to

Symptom

Workaround

All users

After installing this update, you might be unable to change your user account profile picture.

When attempting to change a profile picture by selecting the button Start> Settings> Accounts > Your info, and then selecting Choose a file, you might receive an error message with error code 0x80070520.

After further investigation, we concluded this issue has very limited or no impact for this Windows version.  

If you encounter this issue on a Windows 11, version 21H2 device, please contact Windows support for help. ​​​​​​​

All users

After installing this security update, you might face issues with booting Linux if you have enabled the dual-boot setup for Windows and Linux in your device. Resulting from this issue, your device might fail to boot Linux and show the error message “Verifying shim SBAT data failed: Security Policy Violation. Something has gone seriously wrong: SBAT self-check failed: Security Policy Violation.”

The August 2024 Windows security update applies a Secure Boot Advanced Targeting (SBAT) setting to devices that run Windows to block old, vulnerable boot managers. This SBAT update will not be applied to devices where dual booting is detected. On some devices, the dual-boot detection did not detect some customized methods of dual-booting and applied the SBAT value when it should not have been applied.

The September 2024 Windows security update (KB5043067) and later updates do not contain the settings that caused this issue.

On Windows-only systems, after installing the September 2024 or later updates, you can set the registry key documented in CVE-2022-2601 and CVE-2023-40547 to ensure the SBAT security update is applied.

On systems that dual-boot Linux and Windows, there are no additional steps necessary after installing the September 2024 or later updates.

How to get this update

Before you install this update

Microsoft combines the latest servicing stack update (SSU) for your operating system with the latest cumulative update (LCU). For general information about SSUs, see Servicing stack updates and Servicing Stack Updates (SSU): Frequently Asked Questions

Install this update

To install this update, use one of the following Windows and Microsoft release channels.

Available

Next Step

Yes

None. This update will be downloaded and installed automatically from Windows Update and Microsoft Update.

Available

Next Step

Yes

None. This update will be downloaded and installed automatically from Windows Update for Business in accordance with configured policies.

Available

Next Step

Yes

To get the standalone package for this update, go to the Microsoft Update Catalog website.

Available

Next Step

Yes

This update will automatically sync with Windows Server Update Services (WSUS) if you configure Products and Classifications as follows:

Product: Windows 11

Classification: Security Updates

If you want to remove the LCU

To remove the LCU after installing the combined SSU and LCU package, use the DISM/Remove-Package command line option with the LCU package name as the argument. You can find the package name by using this command: DISM /online /get-packages.

Running Windows Update Standalone Installer (wusa.exe) with the /uninstall switch on the combined package will not work because the combined package contains the SSU. You cannot remove the SSU from the system after installation.

File information

For a list of the files that are provided in this update, download the file information for cumulative update 5041592

For a list of the files that are provided in the servicing stack update, download the file information for the SSU (KB5041591) - version 22000.3139.  

Need more help?

Want more options?

Explore subscription benefits, browse training courses, learn how to secure your device, and more.

Communities help you ask and answer questions, give feedback, and hear from experts with rich knowledge.